- 12 -
ADJUSTMENT INSTRUCTIONS
1. Application Object
These instructions apply to the DLP Projection(Chassis:
MB-042H).
2. Notes
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of an insolation
transformer will help protect test equipment.
(2) The adjustments must be performed in the correct
sequence.
(3) The adjustments must be performed in the condition of
25±5°C of temperature and 65±10% of relative humidity if
there is no other specific designation.
(4) The input voltage of the receiver must keep AC 120V,
60Hz in adjusting.
(5) Unless stated otherwise, the set must be operated for at
least 5 minutes prior to adjustments.
The heat-run should be performed with a 100% white
pattern, but reception of a moving picture may also be
possible in unavoidable cases.
3. Composition of Adjustment Mode
(1) Adjustment modes are entered by pressing the ADJ key
on the Service Remore Control, after adjustments press
the ADJ key to exit.
(2) Initial Adjustment mode menu is shown below. <Fig. 1>
(3) As shown <Fig. 1>, using the CH+ (
D
), CH- (
E
) keys, to
select an item, press the ENTER or (
G
) keys to
enter the appropriate item and begin the adjustment.
(4) Change the value of adjustment by using the (
G
),
volume -(
F
) keys. To change adjustment item, use the
CH+ (
D
), CH- (
E
) keys in ADJ Mode.
(5) Press the ADJ key to exit after adjustments.
(6) Preparation for Adjustment
1) Connect the power to TV Set and set “Power on”.
2) Allow set to Heat-Run for at least 5 minitues before
adjusting.
4. Driver Board Bin Setting
HD3 DMD sets Bias Voltage Bin setting with S/W.
Only, is not the E Type and case of the different DMD sets a
Bin setting value at adjustment mode. (DDP1010 adjustment
item on subordinate position existence)
<Fig. 2> DMD Marking Locations
<Fig. 1> Adjustment Mode OSD
Содержание RU-44SZ63D
