LG MS09AQ Скачать руководство пользователя страница 12

Страница: 12 / 17

CAUTION

Installation Information. For right piping.

Follow the instruction above.

Bad case

- Following bending case from right to left di-

rectly may cause damage to the tubing.

* The feature can be changed according to

type of model.

Installation of Indoor Unit

Hook the indoor unit onto the upper por-

tion of the installation plate.( engage the

three hooks at the top of the indoor unit

with the upper edge of the installation

plate) Ensure that the hooks are properly

seated on the installation plate by moving

it left and right

Unlock the tubing holder from the chassis

and mount between the chassis and instal-

lation plate in order to separate the bottom

side of the indoor unit from the wall.

* The feature can be changed according to

type of model.

Piping

Insert the connecting cable through the

bottom side of indoor unit and connect the

cable (You can see detail contents in 'Con-

necting the cables' section)

View

Terminal block

Connecting cable

Cable retainer

Installation plate

Tubing Holder

INSTALLATION

LIS

Содержание MS09AQ


















Результаты поиска

Содержание MS09AQ

Отзывы:

Похожие инструкции для MS09AQ

Бренды по названию

Популярные бренды

LG MS09AQ, Руководство по установке

Результаты поиска

Содержание MS09AQ

Отзывы:

Похожие инструкции для MS09AQ

Бренды по названию

Популярные бренды