LG MS-1146SQP Скачать руководство пользователя страница 7

Страница: 7 / 33

4-1

FEATURES

CONTROL PANEL

OPERATING INSTRUCTIONS

1. DISPLAY WINDOW:

Used to show time of day,

power level of cooking, cooking category.

2. AUTO COOK:

Used to cook the foods listed by

one touch.

3. AUTO DEFROST:

Used to select the desired auto

weight defrost programmed with weight pad.

4. EXPRESS DEFROST:

Touch this pad to defrost

foods quickly.

5. BREAD DEFROST:

Touch this pad to defrost

bread.

6. CLOCK:

Used to set the time of day.

7. POWER:

Used to select the desired power level for

cooking.

8. TIME:

Touch this pad to set a cook time.

9. NUMBER:

Used to set for time of day, cooking time,

power level or defrost weight.

10. SOFTEN

11. MELT

12. STOP / CLEAR:

Used to stop over and clear all

entries except time of day.

13. START / QUICK START:

To quickly set the

cooking time directly.

Содержание MS-1146SQP


































Результаты поиска

Содержание MS-1146SQP

Отзывы:

Похожие инструкции для MS-1146SQP

Бренды по названию

Популярные бренды

LG MS-1146SQP, Руководство по обслуживанию

Результаты поиска

Содержание MS-1146SQP

Отзывы:

Похожие инструкции для MS-1146SQP

Бренды по названию

Популярные бренды