LG MS-1146SQP Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 33

background image

5-12

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. No input can be

programmed.

Continuity.

No continuity.

Defective PCB
assembly.

Replace PCB
assembly.

Check the conn-
ection between
membrane key
assembly and
PCB assembly.

Replace key
membrane
assembly and
check operation.

2. Some inputs

cannot be
programmed.

4. Random

programming
when touching
other pads.

5. Display is fixed

at some figure
and can not
accept any
input.

3. Display shows a

number or figure
different from one
touched.

Everything works
as specified.

Still have trouble.

Loose
connection.

Connect them
tightly.

Defective key
membrane
assembly.

Replace key
membrane
assembly.

Defective PCB
assembly.

Replace PCB
assembly.

(TROUBLE 1) The following visual conditions indicate a probable defective control circuit.

1. Incomplete segments.

• Segment missing.
• Partial segment missing.
• Digit flickering (NOTE: Slight flickering is normal.)

2. Colon does not turn on or blink.
3. A distinct change in the brightness of one or more numbers in display.
4. One or more digits in the display are not lighting.
5. Display does not count down with time blinking or up with clock operation.
6.Display obviously jumps in time while counting down.
7.Display counts down too fast while cooking.
8.Each indicator light does not turn on after setting cooking cycle.
9.Display time of day does not reappear when cooking is finished.

10.Beep sound is not heard when correct key is touched.

«
...
20
21
22
23
24
...
»

Содержание MS-1146SQP


































Отзывы:

Нет отзывов

Похожие инструкции для MS-1146SQP

Бренд: Oster Страницы: 17

Бренд: Thermador Страницы: 68

Бренд: Garland Страницы: 16

Бренд: Hyundai Страницы: 56

Бренд: Magic Chef Страницы: 48

Бренд: Blomberg Страницы: 96

Бренд: Turbo Air Страницы: 66

Бренд: Maytag Страницы: 6

Бренд: GE Страницы: 48

Бренд: Viking Страницы: 2

BIC8-2KB GK IX-2

Бренд: Pkm Страницы: 56

Бренд: Daewoo Страницы: 12

Бренд: cecotec Страницы: 31

Бренд: Culina Страницы: 16

Бренд: Daewoo Страницы: 30

FED300ASA Control

Бренд: Tappan Страницы: 12

Бренд: Panasonic Страницы: 60

NNH664MF - MICROWAVE -1.2 CUFT

Бренд: Panasonic Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды