LG MS-1071MC Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 36

background image

D. PCB ASSEMBLY REMOVAL

1) Remove the control panel assembly from the

cavity. (Refer to control panel assembly removal
on previous page.)

2) Remove screws which hold the PCB SUB ASS’Y to

the control panel.

3) Disconnect the flat cable from the PCB SUB

ASS’Y and take off the PCB SUB ASS’Y

E. DOOR MAIN ASSEMBLY REMOVAL

1) Open the door.
2) Remove the choke cover cap very carefully with a

flat-blade screwdriver.

CAUTION : Be careful not to damage door seal plate

with the screwdriver.

3) Lift up and push the door.

NOTE:
1. After replacing the door, be sure to check that the

primary switch, monitor switch, and secondary switch
operate normally.

2. After replacing the door, check for microwave energy

leakage with a survey meter. Microwave energy must
be below the limit of 4 mW/cm. (with a 275 ml water
load)

3. When mounting the door assembly to the oven

assembly, be sure to adjust the door assembly parallel
to the chassis. Also adjust so the door has no play
between the inner door surface and oven frame
assembly. If the door assembly is not mounted
properly, microwaves may leak from the clearance
between the door and the oven.

5-4

Door seal plate

Key Membrane

Door Open Button Release

Lever

Button Spring

Control Panel

PCB Sub Asm

Remove choke cover cap

Remove door

Spacer

«
...
12
13
14
15
16
...
»

Содержание MS-1071MC





































Отзывы:

Нет отзывов

Похожие инструкции для MS-1071MC

Бренд: GE Страницы: 16

Бренд: GE Страницы: 28

Бренд: GE Страницы: 60

Бренд: GE Страницы: 2

Бренд: GE Страницы: 31

Бренд: GE Страницы: 28

Advantium SCA2000BCC

Бренд: GE Страницы: 3

Advantium SCA1000

Бренд: GE Страницы: 48

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 14

Бренд: Panasonic Страницы: 163

Бренд: Panasonic Страницы: 8

NE1257R - COMMERCIAL MICROWAVE OVEN

Бренд: Panasonic Страницы: 48

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 116

Бренд: Panasonic Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды