background image

14

INSTALLATION

Step 6: Attach the Oven to the Wall

WARNING

• To avoid risk of personal injury or property 

damage, you will need two people to install this 

microwave oven.

Carefully lift microwave oven and hang it on 

the support tabs at the bottom of the 

mounting plate. Reaching through the upper 

cabinet, thread the power supply cord 

a

 

through the power supply cord hole 

b

 in the 

bottom of the upper cabinet.

Rotate the microwave oven upward so the top 

of the oven is against the bottom of the upper 

cabinet or cabinet frame.

Then insert a bolt down through each hole 

a

 

in the upper cabinet bottom. Tighten the bolts 

until the gap between the upper cabinet and 

microwave oven is closed.

Roof venting installation: Install the ductwork 

through the vent opening in the upper 

cabinet. Use a caulking gun to seal the 

exterior roof opening around the exhaust cap.

a

 Damper

Use the power supply cord clamp 

b

 to bundle 

the power supply cord. Install the power 

supply cord clamp to the inside of the cabinet 

using a screw.

a

 Duct

Grasp the filter screen with one hand holding 

the ring and the other hand holding the 

opposite end. Insert the end of the filter 

screen without the ring into the opening and 

slide towards the side of the microwave oven. 

Insert the ring end of the filter screen into the 

opening and slide the entire screen towards 

the center of the microwave until the screen is 

securely in position. Repeat for the other filter 

screen.

1

2

3

1

2

Содержание MHEC173 Series

















Отзывы: