LG MH6848G Скачать руководство пользователя страница 25

Страница: 25 / 35

5-15

(TROUBLE 3) Display shows all figures set, but oven does not start cooking while

desired program times are set and START pad is touched.

(TROUBLE 4) Oven seems to be operating but little heat is produced in oven load.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1.Setting time does

not count down
when touching
START pad.

2. Fan motor or

oven lamp
do not turn
on.

No continuity.

Continuity.

No continuity.

Continuity.

Check the con-
nection between
connector and
P.C.B assembly.

Defective
secondary switch.

Replace
secondary switch.

Defective P.C.B
assembly.

Replace P.C.B
assembly.

Check continuity
of secondary
switch (with
door closed).

Check fan motor.

Check oven lamp.

Abnormal

Normal

Defective fan motor.

Defective oven lamp.

Replace fan motor.

Replace oven lamp.

Loose connection.

Connect them
tightly.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

Output is low.

Lower than 90% of
rating voltage.

Normal.

Abnormal.

Measure the
output power.

Disconnect the
wire leads from
relay 2 and check
on and off time
with multitester.

Defective P.C.B
assembly.

Replace P.C.B
assembly.

Decrease in power
source voltage
with load.

Suggest customer
contact local
electric power
utility co. or
qualified
electrician.

Check the
power source
voltage.

Defective
magnetron.

Replace
magnetron.

NOTE: Simple test of power output-conducted by heating one liter water for one min. if available.

Minimum 8.5˚C temperature rise is normal condition.

LGE Internal Use Only

Содержание MH6848G



































Результаты поиска

Содержание MH6848G

Отзывы:

Похожие инструкции для MH6848G

Бренды по названию

Популярные бренды

LG MH6848G, Руководство по обслуживанию

Результаты поиска

Содержание MH6848G

Отзывы:

Похожие инструкции для MH6848G

Бренды по названию

Популярные бренды