LG MH6848G Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 35

background image

5-11

COMPONENTS

TEST PROCEDURE

RESULTS

Disconnect the 8 pin
connector from P.C.B.
(Refer to schemetic diagram)

RELAY 2, RELAY 3
OF P.C.B.
(Wire leads removed.)
Note: Relay
Relay 1: Fan motor

Turntable motor
Oven lamp

Relay 2: Microwave
Relay 3: Grill

FAN MOTOR
(Wire leads removed)

TURNTABLE
MOTOR
(Wire leads removed)

Normal: Approx. 200 ~400 ohm

Abnormal:

∞

or several

Ω

Normal: Approx. 10~20

Ω

Abnormal:

∞

or several

Ω

Check for P.C.B. connector.

Measure the resistance.
(Ohm-meter scale: R x 1)

Cooking Start OFF

Cooking Start OFF

1

3

5

Relay 2

Relay 1

Relay 3

A

B

Measure the resistance.
(Ohm-meter scale: R x 1000)

NOTE : • A MICROWAVE LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS

SERVICED FOR ANY REASON.

• MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSITION.
• WHEN REMOVING THE WIRE LEADS FROM THE PARTS, BE SURE TO GRASP THE

CONNECTOR, NOT THE WIRES.

A Approx. 30 ~ 50 ohm

B Approx. 300 ~ 500 ohm

LGE Internal Use Only

Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes

«
...
19
20
21
22
23
...
»

Содержание MH6848G




































Отзывы:

Нет отзывов

Похожие инструкции для MH6848G

Бренд: GE Страницы: 5

Бренд: GE Страницы: 2

Бренд: SEVERIN Страницы: 72

Бренд: Progress Страницы: 36

Бренд: Jenn-Air Страницы: 96

Бренд: Daewoo Страницы: 19

Бренд: Rangemaster Страницы: 40

Бренд: Vanguard Страницы: 38

Бренд: Magic Chef Страницы: 31

Бренд: Parmco Страницы: 18

Бренд: Bartscher Страницы: 88

Бренд: Daewoo Страницы: 17

Бренд: Russell Hobbs Страницы: 22

Бренд: Galanz Страницы: 20

Бренд: G3 Ferrari Страницы: 40

Бренд: Magic Chef Страницы: 41

Бренд: Cookology Страницы: 25

Бренд: Taurus Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды