LG MH6848G Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 35

background image

5-8

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.

(Ohm-meter scale: Rx1 and Rx100))
• Primary winding
• Secondary winding
• Filament winding

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Primary winding to ground
• Filament winding to ground

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Filament to chassis

Approx.: 1.4 ohm
Approx.: 90 ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

COMPONENT TEST PROCEDURE

LGE Internal Use Only

Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes

«
...
16
17
18
19
20
...
»

Содержание MH6848G




































Отзывы:

Нет отзывов

Похожие инструкции для MH6848G

Бренд: Daewoo Страницы: 42

Бренд: Caple Страницы: 26

Бренд: Pit Boss Страницы: 16

Бренд: Galanz Страницы: 13

Бренд: DAEWOO ELECTRONICS Страницы: 27

Бренд: Dacor Страницы: 48

Бренд: Zigmund & Shtain Страницы: 32

Бренд: Franke Страницы: 21

Бренд: GE Страницы: 3

Бренд: Elba Страницы: 27

Бренд: Hotpoint Ariston Страницы: 72

Бренд: montpellier Страницы: 22

Бренд: Daewoo Страницы: 49

Бренд: Malloca Страницы: 16

Бренд: Jade Страницы: 32

Бренд: Asko Страницы: 48

Бренд: Blodgett Страницы: 94

Бренд: Liberton Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды