LG MFL59506845 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 25

background image

2

Unlock the tubing holder from the chassis
and mount between the chassis and instal-
lation plate in order to separate the bottom
side of the indoor unit from the wall.

* The feature can be changed according a

type of model.

Connecting the Piping

1

Pull the screw cap at the bottom of the
indoor unit

2

Remove the chassis cover from the unit by
loosing 3 screws (Be careful not to scratch
Horizontal Vane Main!)

3

Pull back the tubing holder.

4

Remove pipe port cover and positioning
the tubing

* The feature can be changed according a

type of model.

Good case

- Press on the tubing cover and unfold the

tubing to downward slowly. And then bend
to the left side slowly.

11

INSTALLATION

ENGLISH

Tubing holder

Pipe Port

Indoor unit back side view

Left

Backwards

Right

Chassis cover

Tubing Holder

«
...
9
10
11
12
13
...
»

Содержание MFL59506845


























Отзывы:

Нет отзывов

Похожие инструкции для MFL59506845

Бренд: York Страницы: 44

Бренд: Eco Air Страницы: 17

Бренд: Panasonic Страницы: 145

Бренд: Panasonic Страницы: 76

Бренд: Panasonic Страницы: 56

Бренд: Bard Страницы: 12

Split Type Room Air Conditioner

Бренд: Midea Страницы: 14

Бренд: NateoSante Страницы: 52

Бренд: Friedrich Страницы: 74

Бренд: Lennox Страницы: 67

Бренд: TATA Motors Страницы: 32

Бренд: GE Страницы: 48

Бренд: Impecca Страницы: 40

activair SAC16870N

Бренд: Swann Страницы: 20

Бренд: Comfee Страницы: 53

Box-SL IB2-XY 35M

Бренд: CLIVET Страницы: 56

Бренд: Carrier Страницы: 22

Бренд: YMGI Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды