LG MFL59506828 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 31

background image

20

Room Air Conditioner

Installation

Indoor

Connect the cable to the indoor unit by connecting the wires to the terminals on the control board
individually according to the outdoor unit connection. (Ensure that the color of the wires of the
outdoor unit and the terminal No. are the same as those of the indoor unit.)

Connecting the Cables

• The circuit diagram is a subject to change without notice.

• The earth wire should be longer than the common wires.

• When installing, refer to the circuit diagram on the chassis cover.

• Connect the wires firmly so that they may not be pulled out easily.
• Connect the wires according to color codes, referring to the wiring diagram.

Provide a circuit breaker between
power source and the outdoor unit as
shown below.

The power cord connected to the outdoor unit should be complied with the following
specifications (UL recognized or CSA certified).

The power connecting cable connected to the indoor and outdoor unit should be
complied with the following specifications (UL recognized or CSA certified).

Air

Conditioner

Main power source

Circuit Breaker
Use a circuit breaker
or time delay fuse.

GN/YL

20mm

AWG_"B"

Connecting cable (208/230V)

103mm

GN/YL

20mm

Power supply cable (208/230V)

AWG_"A"

103mm

24k/36k

25

Circuit

Breaker

(A)

Capacity(Btu/h)

24k/36k

12

Power

"A"

Capacity(Btu/h)

24k/36k

18

Power

"B"

Capacity(Btu/h)

When using the separate wire as the power cord, please fix the separate wire into the
control box panel by using tie wrap as the fixture.

«
...
18
19
20
21
22
...
»

Содержание MFL59506828
































Отзывы:

Нет отзывов

Похожие инструкции для MFL59506828

Бренд: Haier Страницы: 15

Бренд: Filters Fast Страницы: 10

Бренд: Klarstein Страницы: 64

Бренд: INVENTOR Страницы: 5

Бренд: Soleus Air Страницы: 10

Бренд: Carrier Страницы: 12

Бренд: Daikin Страницы: 24

WAECO VAS 581 001

Бренд: Dometic GROUP Страницы: 328

Бренд: DeLonghi Страницы: 18

Thru-the-Wall Air Conditioners

Бренд: Friedrich Страницы: 6

Бренд: Linea 2000 Страницы: 94

Бренд: mundoclima Страницы: 38

Бренд: Midea Страницы: 19

IonFlow 50 Style

Бренд: Lightair Страницы: 4

Бренд: Seifert Страницы: 23

Бренд: Daikin Страницы: 16

Бренд: Daikin Страницы: 24

Бренд: Daikin Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды