manualshive.com logo in svg

LG LMH1017CVB, Руководство по обслуживанию

Поделиться
Скачать
LG LMH1017CVB Скачать руководство пользователя страница 25

5-14

1. Incomplete segments.

• Segment missing.
• Partial segment missing.
• Digit flickering (NOTE: Slight flickering is normal.)

2. Colon does not turn on or blink.
3. A distinct change in the brightness of one or more numbers in display.
4. One or more digits in the display are not lighting.
5. Display indicates a number different from one touched, for example, key in 5 and 3 appears in the display.
6. Specific numbers (for example 7 or 9) does not display when key pad is touched.
7. Display does not count down with time blinking or up with clock operation.
8. Display obviously jumps in time while counting down.
9. Display counts down too fast while cooking.

10. Each indicator light does not turn on after setting cooking cycle.
11. Display time of day does not reappear when cooking is finished.

(TROUBLE 1) The following visual conditions indicate a probable defective control circuit.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

Everything works
as specified.

Continuity.

No continuity.

Still have trouble.

Defective key
membrane
assembly.

Defective P.C.B
assembly.

Loose
connection.

Defective P.C.B
assembly.

Replace key
membrane
assembly.

Replace P.C.B
assembly.

Connect them
tightly.

Replace P.C.B
assembly.

Replace key
membrane
assembly and
check operation.

Check the conn-
ection between
membrane key
assembly and
P.C.B assembly.

2. Some inputs

cannot be
programmed.

1. No input can be

programmed.

3. Display shows a

number or figure
different from one
touched.

4. Random

programming
when touching
other pads.

5. Display is fixed

at some figure
and can not
accept any
input.

Содержание LMH1017CVB









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды