manualshive.com logo in svg

LG LMH1017CVB, Руководство по обслуживанию

Поделиться
Скачать
LG LMH1017CVB Скачать руководство пользователя страница 20

5-9

COMPONENT TEST PROCEDURE

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.

(Select the ohm scale on the meter)
• Primary winding
• Secondary winding
• Filament winding

2. Measure the resistance.

(Select the ohm scale on the meter)
• Primary winding to ground
• Filament winding to ground

1. Measure the resistance. 

(Select the ohm scale on the meter)
• Filament terminal

2. Measure the resistance.

(Select the ohm scale on the meter)
• Filament to chassis

Approx.: 0.6 ~ 0.9 ohm
Approx.: 70 ~ 90 ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

PRIMARY

TERMINAL

SECONDARY  

FILAMENT 
WINDING

Содержание LMH1017CVB









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды