LG LM-2422A2L/A3L Скачать руководство пользователя страница 47

Страница: 47 / 81

(1) Pumping down

•

Procedure

1. Confirm that both the gas side and liquid side

valves are set to the open position.

- Remove the valve stem caps and confirm that

the valve stems are in the raised position.

- Be sure to use a hexagonal wrench to operate

the valve stems.

2. Operate the unit for 10 to 15 minutes.

3. Stop operation and wait for 3 minutes, then con-

nect the manifold gauge to the service port of
the gas side valve.

- Connect the hose of the gauge with the push

pin to the service port.

4. Air purging of the charge hose.

- Open the Low-handle valve on the gauge

slightly to air purge from the hose.

5. Set the liquid side valve to the closed position.

6. Operate the air conditioner at the cooling cycle

and stop it when the gauge indicates 1kg/cm

7. Immediately set the gas side valve to the closed

position.

- Do this quickly so that the gauge ends up indi-

cating 1kg/cm

8. Disconnect the charge set, and mount the liquid

side and gas side valve caps and the service
port nut.

- Use torque wrench to tighten the service port

nut to a torque of 1.8kg.m.(4.2kg.m/5.5kg.m)

- Be sure to check for gas leakage.

9. Apply steps from 1 to 8 to each unit (A-unit, B-

unit) by the same method.

- 47 -

Indoor unit

Outdoor unit

Liquid side

Gas side

2-Way

valve

Open

3-Way

valve

manifold gauge

Hi- handle

(CLOSE)

Low-handle

(CLOSE)

Содержание LM-2422A2L/A3L


















































































Результаты поиска

Содержание LM-2422A2L/A3L

Отзывы:

Похожие инструкции для LM-2422A2L/A3L

Бренды по названию

Популярные бренды

LG LM-2422A2L/A3L, Руководство по обслуживанию

Результаты поиска

Содержание LM-2422A2L/A3L

Отзывы:

Похожие инструкции для LM-2422A2L/A3L

Бренды по названию

Популярные бренды