LG LGES-5048 Скачать руководство пользователя страница 9

Страница: 9 / 37

Smart Meter

Battery

On-Grid

Battery

Back-Up

On-Grid

Back-Up

Incompatible battery

Generator

Back-Up

Load

On-Grid

02 Installation Instructions

2.1 Unacceptable Installations

Please avoid the following installations which will damage the system or the Inverter.
The following installations should be avoided. Any damage caused will not be covered by the warranty
policy.

For the general version, backup cannot connect in parallel.
For advanced applications, please contact our Tech Support
Dept

Single PV string cannot connect to multiple inverters.

One meter cannot be connected to multiple inverters.
Different CTs cannot connect to the same line cable.

The On-Grid or back-up side cannot be
connected to any AC generator directly.

The inverter battery input must not be
connected to incompatible batteries.

The backup side cannot be connected
to the grid.

One battery bank cannot be connected to multiple inverters.

2.2 Packing List

Upon receiving the hybrid inverter, please check if any of the components as shown below are
missing or broken.

Terminal

Expansion

Bolts

Fixed

Screw

Positive PV Plug

Battery Cover

Negative PV Plug

Inverter

Documentations

Smart Meter With CT

Wall-Mounted

Bracket

Reset

SMART METER

Battery

Terminal

Hexagon

screw

WiFi

Module

Bluetooth

Module

Clip

Содержание LGES-5048






































Результаты поиска

Содержание LGES-5048

Отзывы:

Бренды по названию

Популярные бренды

LG LGES-5048, Руководство пользователя

Результаты поиска

Содержание LGES-5048

Отзывы:

Бренды по названию

Популярные бренды