manualshive.com logo in svg

LG LGES-5048, Руководство пользователя

Поделиться
Скачать
LG LGES-5048 Скачать руководство пользователя страница 5

2

1.2 Safety and Warning

LGES-5048 from LG Energy Solution Ltd strictly complies with related safety rules for product design 
and testing. Please read and follow all the instructions and cautions on the inverter or user
manual during installation, operation or maintenance. Improper operation might cause personal
or property damage.

Symbol Explanation

Danger - high voltage and electric shock!

Caution! 
Failure to observe any warnings contained in this manual may result in injury.

Danger - hot surface!

The components of the product can be recycled.

This side up! This package must always be transported, handled and stored in such a way 
that the arrows always point upwards.

No more than six (6) identical packages being stacked on each other.

Products shall not be disposed as household waste.

5min

Fragile - The package/product should be handled carefully and never be tipped over or 
slung. 

Refer to the operating instructions.

Keep dry!  The package/product must be protected from excessive humidity and must be 
stored under cover. 

This symbol indicates that you should wait at least 5mins after disconnecting the inverter from 
the utility grid and from the PV panel before touching any inner live parts.

CE mark.

Содержание LGES-5048






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды