LG LG-YD636 Скачать руководство пользователя страница 10

Страница: 10 / 55

processor, digital FM (DFM) processor, QCT’s latest generation of DSP, the QDSP4000™ core, for

voice compression and applications support, PLL and an ARM® ARM7TDMI microprocessor. Also

integrated in the MSM6025 device are analog functions such as a wideband mono codec and analog

interfaces for the radioOne RF ASICs. Controllers for a universal serial bus (USB), device controller

for an R-UIM (CDMA SIM), GPIOs, and peripheral interfaces complete the system integration. And the

MSM6025 chipset and system software are designed to support IS95A/95B and Release 0 of

CDMA2000 standards.

In MSM, coded symbols are interleaved in order to cope with multi-path fading. Each data channel is

scrambled by the long code PN sequence of the user in order to ensure the confidentiality of calls.

Moreover, binary quadrature codes are used based on walsh functions in order to discern each

channel. Data created thus are 4-phase modulated by one pair of Pilot PN code and they are used to

create I and Q data.

When received, I and Q data are demodulated into symbols by the demodulator, and then

de-interleaved in reverse to the case of transmission. Then, the errors of data received from viterbi

decoder are detected and corrected. They are voice-decoded at the vocoder in order to output digital

voice data.

2.3.4 Memory Part

Memory part consists of 64 Mbits Flash Memory and 32 Mbits Static RAM. the Flash Memory part are

programs used for terminal operation. The programs can be changed through down loading after the

assembling of terminals. On the SRAM data generated during the terminal operation are stored

temporarily.

2.3.5 UIM Part

The MSM6025 is supports RUIM.

The UIM card contains the informations of phone number, PIM data, SMS data, etc.

The whole circuits are designed to operate 2.85V UIM cards.

2.3.6 Power Supply Part

Turn On

When the battery voltage (4.2V ~ 3.2V) is fed and the PWR key of keypad is pressed, PMIC is

activated by the PWR_ON_SW/ signal, and then the control signal PS_HOLD signal is generated.

And then, the regurator 1.9V_MSMC & 2.85V_MSMP, 2.6V_MSMA, are operated.

Operating

During the phone is on operating state,

LDO(in PMIC) for MSM is always enable and gives the power MSM6025 and memory part

Содержание LG-YD636
























































Результаты поиска

Содержание LG-YD636

Отзывы:

Похожие инструкции для LG-YD636

Бренды по названию

Популярные бренды

LG LG-YD636, Руководство по обслуживанию

Результаты поиска

Содержание LG-YD636

Отзывы:

Похожие инструкции для LG-YD636

Бренды по названию

Популярные бренды