LG LG-YD636 Скачать руководство пользователя страница 54

Страница: 54 / 55

position the antenna up and over your shoulder.

Do not hold the antenna when the phone is “IN USE”. Holding the antenna affects call quality and may

cause the phone to operated at a higher power level than needed.

Antenna Care and Replacement

▣

Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with skin, a

minor bum may result. Replace a damaged antenna immediately. Consult your manual to see if you

may change your antenna yourself. If so, use only a manufacture approves antenna. Otherwise, take

your phone to a qualifies service center for repair.

Use only the supplied or approved antenna. Non-approved antennas, modifications, or attachments,

could impair call quality, damage the phone, and violate FCC egulations.

Driving

▣

Check the laws and regulations on the use of cellular telephones in the areas where you drive. Always

obey them. Also, when using your phone while driving, please:

Give full attention to the driving. Use hands-free operation, if available, and pull off the road and park

before making or answering a call if driving conditions require

Electronic Devices

▣

Most modem electronic equipment is shielded from RF energy. However, RF energy from cellular

telephones may affect inadequately shielded electronic equipment.

RF energy may effect improperly installed or inadequately shielded electronic operating and

entertainment system in motor vehicles. Check with the manufacturer or its representative to

determine if these systems are adequately shielded from external RF energy. You should check with

the manufacturer of any equipment that has been added to your vehicle.

Consult the manufacturer of any personal medical devices (such as pacemakers, hearing aids, etc.) to

determine if they are adequately shielded from external RF energy.

Turn your phone OFF in health care facilities. When any regulations posted in the areas

instruct you

to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external

RF energy.

Содержание LG-YD636
























































Результаты поиска

Содержание LG-YD636

Отзывы:

Похожие инструкции для LG-YD636

Бренды по названию

Популярные бренды

LG LG-YD636, Руководство по обслуживанию

Результаты поиска

Содержание LG-YD636

Отзывы:

Похожие инструкции для LG-YD636

Бренды по названию

Популярные бренды