LG LG- PX240 Скачать руководство пользователя страница 83

Страница: 83 / 96

Channel.

Transmit Objective Loudness Rating(TOLR).

A perceptually weighted transducer gain of telephone

transmitters relation sound pressure at the microphone to voltage at a reference electrical termination. It is

normally specified in dB relative to one millivolt per Pascal. See IEEE Standard 269-1992, IEEE Standard

661-1979, CCITT Recommendation P.76 , and CCITT Recommendation. P.79

Unique Challenge-Response Procedure.

An exchange of information between a mobile station and a base

station for the purpose of confirming the mobile station’s identity. The procedure is initiated by the base station

and is characterized by the use of a challenge-specific random number(i.e., RANDU) instead of the random

variable broadcast globally(RAND).

Unique Random Variable(RANDU).

A 24-bit random number generated by the base station in support of the

Unique Challenge-Response procedure.

Universal Coordinated Time(UTC).

An internationally agreed-upon time scale maintained by the Bureau

International de l’Heure(BIH) used as the time reference by nearly all commonly available time and frequency

distribution systems i.e., WWW, WWVH, LORAN-C, Transit, Omega, and GPS.

UTC.

Universal Temps Coordine. See Universal Coordinated Time.

Voice Channel

. See Analog Voice Channel.

Voice Mobile Attenuation Code(VMAC).

A 3-bit field in the Extended Address Word commanding the initial

mobile power level when assigning a mobile station to an analog voice channel.

Voice Privacy.

The process by which user voice transmitted over a CDMA Traffic Channel is a afforded a

modest degree of protection against eavesdropping over the air.

Walsh Chip.

The shortest identifiable component of a Walsh function. There are 2

Walsh chips in one

Walsh function where N is the order of the Walsh function. On the Forward CDMA channel one Walsh chip

equals 1/1.2288MHz, or 813.802…ns. On the Reverse CDMA Channel, one Walsh chip equals 4/1.2288MHz,

or 3.255…

㎲

Walsh Function

. One of 2

time orthogonal binary functions (note that the functions are orthogonal after

mapping ‘0’ to 1 and ‘1’ to –1).

Zone-Based Registration

. An autonomous registration method in which the mobile station registers whenever it

enters a zone that is not in the mobile station’s zone list.

㎲

Microsecond

Z3X-BOX.COM

Содержание LG- PX240

































































































Результаты поиска

Содержание LG- PX240

Отзывы:

Похожие инструкции для LG- PX240

Бренды по названию

Популярные бренды

LG LG- PX240, Руководство по обслуживанию

Результаты поиска

Содержание LG- PX240

Отзывы:

Похожие инструкции для LG- PX240

Бренды по названию

Популярные бренды