LG LG- PX240 Скачать руководство пользователя страница 8

Страница: 8 / 96

2. Installation

2.1 Installing a Battery Pack

1) The Battery pack is keyed so it can only fit one way. Align the groove in the battery pack with the rail on the

back of the phone until the battery pack rests flush with the back of the phone.

2) Slide the battery pack forward until you hear a “click”, which locks the battery in place.

2.2 For Adapter Use

1) Plug the adapter into a wall outlet. The adapter can be operated from a 110V source. When AC power is

connected to the adapter.

2) Insert the adapter jack into the phone with the installed battery pack.

Red light indicates battery is being charged.. Green light indicates battry is fully charged.

2.3 For Mobile Mount

2.3.1 Installation Position

In order to reduce echo sound when using the Hands-Free Kit, make sure that the speaker and microphone are

not facing each other and keep microphone a generous distance from the speaker.

2.3.2 Microphone Installation

Install the microphone either by clipping I onto the sunvisor (driver’s side) or by attaching it to door post

(driver’s side), using a velcno adhesive tape (not included).

2.3.3 Cable Connections

2.3.3.1 Power and Ignition Cables

Connect the red wire to the car battery positive terminal and the black wire to the car ground. Connect the

green wire to the car ignition sensor terminal. ( In order to operate HFK please make sure to connect green wire

to ignition sensor terminal.) Connect the kit’s power cable connector to the interface box power receptacle.

2.3.3.2 Antenna Cable Connection

Connect the antenna coupler cable connector from the cradle to the external antenna connector. ( Antenna is

not included.)

Z3X-BOX.COM

Содержание LG- PX240

































































































Результаты поиска

Содержание LG- PX240

Отзывы:

Похожие инструкции для LG- PX240

Бренды по названию

Популярные бренды

LG LG- PX240, Руководство по обслуживанию

Результаты поиска

Содержание LG- PX240

Отзывы:

Похожие инструкции для LG- PX240

Бренды по названию

Популярные бренды