LG LFC23760SB Скачать руководство пользователя страница 26

Страница: 26 / 46

6-5 REFRIGERATION CYCLE

• Troubleshooting Chart

- 24 -

¥
¥

CAUSE

TEMPERATURE

OF THE

COMPRESSOR

REMARKS

STATE OF

THE UNIT

STATE OF THE

EVAPORATOR

LEAKAGE

RESTRICTION

DEFECTIVE

COMPRESSION

PARTIAL
LEAKAGE

Freezer
compartment and
refrigerator don’t
cool normally

COMPLETE
LEAKAGE

PARTIAL
RESTRICTION

COMPLETE
RESTRICTION

MOISTURE
RESTRICTION

COMPRE-
SSION

NO
COMPRE-
SSION

Freezer
compartment and
refrigerator don’t
cool normally

Freezer
compartment and
refrigerator don’t
cool.

Cooling operation
stops periodically.

Freezer and
refrigerator don’t
cool.

No compressing
operation.

Low flowing sound of
refrigerant is heard and frost
forms in inlet only.

Flowing sound of refrigerant
is not heard and frost isn’t
formed.

Flowing sound of refrigerant
is heard and frost forms in
inlet only.

Flowing sound of refrigerant
is not heard and frost isn’t
formed.

Flowing sound of refrigerant
is not heard and frost melts.

Low flowing sound of
refrigerant is heard and frost
forms in inlet only.

Flowing sound of refrigerant
is not heard and there is no
frost.

A little higher than
ambient
temperature.

- Refrigerant level is low due to a
leak.
- Normal cooling is possible by
restoring the normal amount of
refrigerant and repairing the leak.

Equal to ambient
temperature.

- No discharging of refrigerant.
- Normal cooling is possible by
restoring the normal amount of
refrigerant and repairing the leak.

A little higher than
ambient
temperature.

- Normal discharging of the
refrigerant.
- The capillary tube is faulty.

Equal to ambient
temperature.

- Normal discharging of the
refrigerant.

Lower than ambient
temperature.

- Cooling operation restarts when
heating the inlet of the capillary
tube.

A little higher than
ambient
temperature.

- Low pressure at high side of
compressor due to low
refrigerant level.

Equal to ambient
temperature

- No pressure in the high
pressure part of the compressor.

Содержание LFC23760SB















































Результаты поиска

Содержание LFC23760SB

Отзывы:

Бренды по названию

Популярные бренды

LG LFC23760SB, Руководство по обслуживанию

Результаты поиска

Содержание LFC23760SB

Отзывы:

Бренды по названию

Популярные бренды