background image

Service Manual 

9

Window Requirements

All supporting parts should be secured to firm

wood, masonry, or metal.

1. This unit is designed for installation in standard double

hung windows with actual opening widths of 21" to 35".

The upper and lower sash must open sufficiently to allow

a clear vertical opening of 12" from the bottom of the

sash to the window stool.

2. If storm window presents interference, fasten a 2" wide

wood strip to the inner window sill across the full width of

the sill. The wood strip should be thick enough to raise

the height of the window sill so that the unit can be

installed without interference by the storm window frame.

See Figure. 3. Top of wood strip should be approximately

3/4" higher than the storm window frame (STORM WIN-

DOW FRAME) or wood strip (OUTDOORS) to help con-

densation to drain properly to the outside.

3. Install a second wood strip (approximately 6" long by

11/2" wide and same thickness as first strip) in the center

of the outer sill flush against the back off the inner sill.

This will raise the L bracket as shown Figure. 3.

4. If the distance between STORM WINDOW FRAME and

WOOD STRIP MOUNTED ON TOP OF INNER SILL is

more than 1", two of wood strip are not necessary.

NOTICE

Installation

Installation

Select the Best Location

How to Install

This air conditioner is designed with a button-down chassis so it can be easily installed in a window. 

1. To prevent vibration and noise, make sure the unit is

installed securely and firmly.

2. Install the unit where the sun does not shine directly on

the unit.

3. The outside of the cabinet must extend outward for at

least 10" and there should be no obstacles, such as a

fence or wall, within 20" from the back of the cabinet

because it will prevent heat radiation of the condenser.

Restriction of outside air will greatly reduce the cooling

efficiency of the air conditioner.

CAUTION: All side louvers of the cabinet

must remain exposed on the outdside of

the structure.

4. Install the unit slanted slightly so the back is slightly

lower than the front (about 1/4"). This will force con-

densed water to the outside.

5. Install the unit with the bottom about 30"~60" above the

floor level. 

ABOUT  / "

Over 20"

HEAT

RADIATION

FENCE

AWNING

OUTSIDE 

INSIDE

COOLED AIR

30"-60"

1

2

OUTDOORS

INDOORS

INNER SILL

OUTER

SILL

INNER

SILL

WOOD STRIP MOUNTED

ON TOP OF INNER SILL

WOOD STRIP

FOR 

L

 BRACKET

3

/

4

"

CLEARANCE

1" MAX.

STORM

WINDOW

FRAME

OUTDOORS

INDOORS

OUTER

SILL

Figure 1

Figure 2

Figure 3

Содержание L5004R



































Отзывы: