LG L5004R, Руководство по обслуживанию

Страница: 17 / 34

Disassembly Disassembly Disassembly Disassembly
le R erating Cyc
Refrigerating Cycle
10. CAPACITOR
1. Remove the cabinet. (Refer to Section 2)
2. Remove the control panel. (Refer to Section 3)
3. Discharge the capacitor by placing a 20 K resistor
across the capacitor terminals.
4. Remove all the leads of capacitor terminals.
5. Re-install the components by referring to the removal
procedure above. (See Figure 26)
11. THERMISTOR
1. Remove the cabinet. (Refer to Section 2)
2. Remove the control panel. (Refer to Section 3)
3. Remove the main PCB inside the control box.
4. Remove the thermostat.
5. Re-install the components by referrig to the
temoval procedure above.
12. POWER CORD
1. Disconnect the unit from source of power.
2. Remove the front grille. (Refer to Section 1)
3. Remove the cabinet. (Refer to Section .2)
4.
box. (Refer to Section 3)
5. Pull the power cord. (See Figure 29)
6. Re-install by referring to procedures above.
1. Remove the cabinet. (Refer to Section 2)
2. Discharge the refrigerant by using a refrigerant recovery
system.
3. Remove 2 screws which fasten the condenser.
(See Figure 30)
4. After discharging the refrigerant completely, unbraze the
interconnecting tube at the condenser connections.
5. Remove the condenser.
6. Re-install by referring to the procedures above.
10. CAPACITOR
1. Remove the cabinet. (Refer to Section 2)
2. Remove the control panel. (Refer to Section 3)
3. Discharge the capacitor by placing a 20 K resistor
across the capacitor terminals.
4. Remove all the leads of capacitor terminals.
5. Re-install the components by referring to the removal
procedure above. (See Figure 26)
11. THERMISTOR
1. Remove the cabinet. (Refer to Section 2)
2. Remove the control panel. (Refer to Section 3)
3. Remove the main PCB inside the control box.
4. Remove the thermostat.
5. Re-install the components by referrig to the
temoval procedure above.
1. Disconnect the unit from source of power.
2. Remove the front grille. (Refer to Section 1)
3. Remove the cabinet. (Refer to Section .2)
4.
box. (Refer to Section 3)
5. Pull the power cord. (See Figure 29)
6. Re-install by referring to procedures above.
1. Remove the cabinet. (Refer to Section 2)
2. Discharge the refrigerant by using a refrigerant recovery
system.
3. Remove 2 screws which fasten the condenser.
(See Figure 30)
4. After discharging the refrigerant completely, unbraze the
interconnecting tube at the condenser connections.
5. Remove the condenser.
6. Re-install by referring to the procedures above.
10. CAPACITOR
1. Remove the cabinet. (Refer to Section 2)
2. Remove the control panel. (Refer to Section 3)
3. Discharge the capacitor by placing a 20 K resistor
across the capacitor terminals.
4. Remove all the leads of capacitor terminals.
5. Re-install the components by referring to the removal
procedure above. (See Figure 26)
11. THERMISTOR
1. Remove the cabinet. (Refer to Section 2)
2. Remove the control panel. (Refer to Section 3)
3. Remove the main PCB inside the control box.
4. Remove the thermostat.
5. Re-install the components by referrig to the
temoval procedure above.
1. Disconnect the unit from source of power.
2. Remove the front grille. (Refer to Section 1)
3. Remove the cabinet. (Refer to Section .2)
4.
box. (Refer to Section 3)
5. Pull the power cord. (See Figure 29)
6. Re-install by referring to procedures above.
1. Remove the cabinet. (Refer to Section 2)
2. Discharge the refrigerant by using a refrigerant recovery
system.
3. Remove 2 screws which fasten the condenser.
(See Figure 30)
4. After discharging the refrigerant completely, unbraze the
interconnecting tube at the condenser connections.
5. Remove the condenser.
6. Re-install by referring to the procedures above.
10. CAPACITOR
1. Remove the cabinet. (Refer to Section 2)
2. Remove the control panel. (Refer to Section 3)
3. Discharge the capacitor by placing a 20 K resistor
across the capacitor terminals.
4. Remove all the leads of capacitor terminals.
5. Re-install the components by referring to the removal
procedure above. (See Figure 26)
11. THERMISTOR
1. Remove the cabinet. (Refer to Section 2)
2. Remove the control panel. (Refer to Section 3)
3. Remove the main PCB inside the control box.
4. Remove the thermostat.
5. Re-install the components by referrig to the
temoval procedure above.
1. Disconnect the unit from source of power.
2. Remove the front grille. (Refer to Section 1)
3. Remove the cabinet. (Refer to Section .2)
4. Remove a screw that secures control panel to control
box. (Refer to Section 3)
5. Pull the power cord. (See Figure 29)
6. Re-install by referring to procedures above.
13. CONDENSER
1. Remove the cabinet. (Refer to Section 2)
2. Discharge the refrigerant by using a refrigerant recovery
system.
3. Remove 2 screws which fasten the condenser.
(See Figure 30)
4. After discharging the refrigerant completely, unbraze the
interconnecting tube at the condenser connections.
5. Remove the condenser.
6. Re-install by referring to the procedures above.
Figure 26
Figure 27
Figure 29
Figure 30
Service Manual 17