background image

20

CAUTION

CAUTION

1

2

When the air conditioner is not going to be used for a long time.

Operation Tips

Helpful information

The air filters and your electiric bill.
If the air filters become clogged with dust, the
cooling capacity will drop, and 6% of the
electricity used to operate the air conditioner will
be wasted.

When it is not going to be used for 

a long time.

When the air conditioner is to 

be used again.

Operate the air conditioner on Air circulation
mode (Refer to page 15) for 2 to 3 hours.

• This will dry out the internal parts.

Turn off the circuit breaker when the air conditioner
is not going to be used for a long time. 

Dirt may collect and may cause a fire.

n

Check that the air inlet and outlet of the
indoor/outdoor unit are not blocked.

Do not overcool the room.

This is not good for the health
and wastes electricity.

Keep blinds or curtains

closed.

Do not let direct sunshine
enter the room when the air
conditioner is in operation.

Make sure that the doors 

and windows are shut tight.

Avoid opening doors and
windows as much as possible
to keep the cool air in the
room.

Clean the air filter regularly.

Blockages in the air filter
reduce the airflow and lower
cooling and dehumidifying
effects. Clean at least once
every two weeks.

Ventilate the room

occasionally.

Since windows are kept
closed, it is a good idea to
open them and ventilate the
room now and then.

Turn off the circuit breaker.

Содержание JB-Q18GB2A0



















































Отзывы: