manualshive.com logo in svg

LG Hydro Kit ARNH30GK1A4, Руководство по установке, Страница: 40 / 111

Поделиться
Скачать
LG Hydro Kit ARNH30GK1A4 Скачать руководство пользователя страница 40

40

ACCESSORIES INSTALLATION

ENGLISH

CAUTION

!

• Install the drain pan when cooling. 
• If not installed, water may form.
• Please refer to separate installation manual when installing drain pan.

Following location should be avoid to secure proper operation :

- Height from floor is approximately 1.5 m.

- Thermostat can not be located where the area may be hidden when door is open.

- Thermostat can not be located where external thermal influence may be applied. (such as above

heating radiator or open window)

Thermostat

Thermostat is generally used to control the product by air temperature. When thermostat is
connected to the product, the product operation is controlled by the thermostat.

Installation condition

Before Installation

CAUTION

!

• USE 220-240 V~ Thermostat
• Some electro-mechanical type thermostat has internal delay time to protect compressor.

In that case, mode change can takes time more than user's expectation. Please read
thermostat manual carefully if the unit does not response quickly.

• Setting temperature range by thermostat can be different with that of the unit. The heating

or cooling set temperature should be chosen within the setting temperature range of the
unit.

• It is highly recommended that the thermostat should be installed where space heating is

mainly applied.

WARNING

!

Followings should be kept before installation
• Main power must be turned off during installing 3rd party accessories.
• 3rd party accessories should be comply with supported specification.
• Proper tools should be chosen for installation.
• Never do installation with wet hands.

ACCESSORIES INSTALLATION

Hydro Kit 

can interface to various accessories to extend its functionality and to improve user

convenience. In this chapter, specifications about supported 3rd party accessories and how to
connect to 

Hydro Kit 

is introduced.

It is noted that this chapter only deal with 3rd party accessories. For accessories supported by LG
Electronics, please refer to installation manual of each accessories.

Содержание Hydro Kit ARNH30GK1A4
















































































































Отзывы:

Нет отзывов