LG GR-562 Скачать руководство пользователя страница 9

Страница: 9 / 46

- 9 -

3-1 DOOR

●

Freezer Door

1. Remove the hinge cover by pulling it upwards.
2. Loosen hexagonal bolts fixing the upper hinge to the

body and lift the freezer door.

3. Pull out the door gasket to remove from the door foam Ass'y.

●

Refrigerator Door

1. Loosen hexagonal bolts fixing the lower hinge to the

body to remove the refrigerator door only.

2. Pull out the door gasket to remove from the door foam Ass'y.

3-2 DOOR SWITCH

1. To remove the door switch, pull out it with a '—' type

driver as shown in (figure 9).

2. Disconnect the lead wire from the switch.

3-3 FAN AND FAN MOTOR

1. Remove the freezer shelf.
2. Remove the Cover Lamp-F and Case Lamp by

loosening 1 screw fixed to ceiling of Inner Case.

3. Remove the Grille by pulling it out.
4. Pull out the Shroud and remove the Fan Motor Assy by

loosening 2 screws.

5. Pull out the fan and, separate the Fan Motor, Brackets

and the Guide Fan.

BOLT

HINGE

HINGE COVER

Figure 6

GASKET

Figure 7

LOWER HINGE

BOLT

Figure 9

3. DISASSEMBLY

GUIDE FAN

FAN

SHROUD

GRILLE

FAN MOTOR

Figure 12

Figure 11

GR-R562/R602

BOLT

HINGE

HINGE COVER

Figure 6-1

GR-S562/S602, GR-562/602

Figure 8

Содержание GR-562















































Результаты поиска

Содержание GR-562

Отзывы:

Бренды по названию

Популярные бренды

LG GR-562, Руководство по обслуживанию

Результаты поиска

Содержание GR-562

Отзывы:

Бренды по названию

Популярные бренды