LG gr-392 Скачать руководство пользователя страница 13

Страница: 13 / 18

6-5 SERVICE DIAGNOSIS CHART

COMPLAINT

POINTS TO BE CHECKED

REMEDY

Cooling is

¥ Is the power cord unplugged from the outlet?

¥ Plug to the outlet.

impossible.

¥ Check if the power S/W is setted to OFF.

¥ Set the switch to ON.

¥ Check if the fuse of power S/W is shorted.

¥ Replace a regular fuse.

¥ Measure the voltage of power outlet.

¥ If voltage is low, wire newly.

Cooling ability

¥ Check if the set is placed close to wall.

¥ Place the set with the space of about 10cm.

is poor.

¥ Check if the set is placed close to stove, gas

¥ Place the set apart from these heat

cooker and direct rays.

appliances.

¥ Is the ambient temperature high or

¥ Make the ambient temperature below.

the room door closed?

¥ Check if putting in hot foods.

¥ Put in foods after they get cold.

¥ Did you open the door of the set too often

¥ Don't open the door too often and closed

or check if the door is closed up?

it firmly.

¥ Check if the Thermostat is set to "WARM (1)".

¥ Set the knob to "MID (2)".

Foods in the

¥ Are foods placed in cooling air outlet?

¥ Place foods in high temperature section.

Refrigerator

(Front Part)

are frozen.

¥ Check if the Thermostat is set to "COLD (3)".

¥ Set the knob to "MID (2)".

¥ Is the ambient temperature within 5¡C?

¥ Set the knob to "WARM (1)".

Dew or ice

¥ Is watery foods kept?

¥ Seal up watery foods with wrap.

forms in the

¥ Check if putting in hot foods.

¥ Put in foods after they get cold.

chamber of

¥ Did you open the door of the set too

¥ Don't open the door too often and close

the set.

often or check if the door is closed up.

it firmly.

Dew forms

¥ Check if ambient temperature and humidity

¥ Wipe dew with a dry cloth. This happening

in the out Case.

are high.

is solved in low temperature and humidity

¥ Is the gap in the door packing?

naturally.

¥ Fill up the gap.

Abnormal

¥ Is the set positioned in a firm and even place?

¥ Adjust the Adjust Screw, and position

noise generates.

in the firm place.

¥ Does any unnecessary objects exist

¥ Remove the objects.

in the back side of the set?

¥ Check if the Drip Tray is omitted.

¥ Place it on an original position.

¥ Check if the cover of mechanical room

¥ Place the cover at an original position.

in below and front side is taken out.

To close the door

¥ Check if the door packing becomes dirty

¥ Clean the door packing.

is not handy.

by filth such as juice.

¥ Is the set positioned in a firm and even place?

¥ Position in the firm place and adjust the

¥ Are too much foods putted in the set?

Adjust Screw.

¥ Keep foods not to reach to the door.

Ice and foods

¥ Check if the inside of the set becomes dirty.

¥ Clean the inside of the set.

smell unpleasant.

¥ Did you keep smelly foods without wraping?

¥ Wrap smelly foods.

¥ It smells plastic.

¥ The new products smell plastic, but it is

removed after 1-2 weeks.

- 13 -

Содержание gr-392



















Результаты поиска

Содержание gr-392

Отзывы:

Похожие инструкции для gr-392

Бренды по названию

Популярные бренды

LG gr-392, Руководство по обслуживанию

Результаты поиска

Содержание gr-392

Отзывы:

Похожие инструкции для gr-392

Бренды по названию

Популярные бренды