manualshive.com logo in svg

LG GoldStar MS-133SE, Руководство по обслуживанию

Поделиться
Скачать
LG GoldStar MS-133SE Скачать руководство пользователя страница 16

K. REMOVING THE TURNTABLE MOTOR

1) Remove the glass turntable.
2) Remove the rotating ring ass’y by hand.
3) Remove the turntable motor cover.

The turntable base cover is easily removed by

pinching the six parts with wire cutting pliers.

4) Disconnect the leadwire from the turntable motor

terminals.

5) Remove the screw securing the turntable motor to

the oven cavity assembly.

6) After repairing the motor, rotate the removed

turntable motor cover.

7) Fit the turntable motor cover's projecting part to the

base plate slit.

NOTE:
1. Remove the wire lead from the turntable motor

VERY CAREFULLY.

2. Be sure to grasp the connector, not the wires,

when removing.

L. INTERLOCK SYSTEM

1) INTERLOCK MECHANISM

The door lock mechanism is a device which has
been specially designed to eliminate completely
microwave activity when the door is opened during
cooking and thus to prevent the danger resulting
from the microwave leakage.

2) MOUNTING OF THE PRIMARY/MONITOR/

SECONDARY SWITCHES TO THE LATCH
BOARD

5-6

Wire Leads

Turntable Motor

PRIMARY
SWITCH

ADJUSTMENT
DIRECTION

MONITOR
SWITCH

SECONDARY
SWITCH

3) INSTALLATION AND ADJUSTMENT OF THE

LATCH BOARD TO THE OVEN ASSEMBLY

• Mount the latch board to the oven assembly.
• Adjust the latch board in the arrow direction so that

oven door will not have any play in it when the door
is closed.

• Tighten the mounting screw.
• Check for play in the door by pushing the door

release button. Door movement should be less
than 0.5 mm. (1/64 inch)

Don't push the door release button while making this

adjustment. Make sure that the latch moves
smoothly after adjustment is completed and that the
screws are tight. Make sure the primary, monitor,
and secondary switches operate properly by
following the continuity test procedure.

Содержание GoldStar MS-133SE








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды