LG GoldStar MS-133SE страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 39

background image

D. PCB ASSEMBLY REMOVAL

1) Remove the control panel assembly from the

cavity. (Refer to control panel assembly removal
on previous page.)

2) Remove screws which hold the PCB SUB ASS’Y to

the control panel.

3) Disconnect the flat cable from the PCB SUB

ASS’Y and take off the PCB SUB ASS’Y

E. DOOR MAIN ASSEMBLY REMOVAL

1) Open the door.
2) Remove the choke cover cap very carefully with a

flat-blade screwdriver.

CAUTION : Be careful not to damage door seal plate

with the screwdriver.

3) Lift up and push the door.

NOTE:
1. After replacing the door, be sure to check that the

primary switch, monitor switch, and secondary switch
operate normally.

2. After replacing the door, check for microwave energy

leakage with a survey meter. Microwave energy must
be below the limit of 4 mW/cm. (with a 275 ml water
load)

3. When mounting the door assembly to the oven

assembly, be sure to adjust the door assembly parallel
to the chassis. Also adjust so the door has no play
between the inner door surface and oven frame
assembly. If the door assembly is not mounted
properly, microwaves may leak from the clearance
between the door and the oven.

F. AIR DUCT ASSEMBLY REMOVAL

1) Disconnect the leadwire from lamp and MGT

thermostat.

2) Remove the mounting screw to the magnetron.

5-4

Door seal plate

Key Membrane

Door Open Button Release

Lever

Button Spring

Control Panel

PCB Sub Asm

Remove choke cover cap

Remove door

Spacer

«
...
12
13
14
15
16
...
»

Содержание GoldStar MS-133SE








































Отзывы:

Нет отзывов

Похожие инструкции для GoldStar MS-133SE

Бренд: Candy Страницы: 14

Discovery EO127

Бренд: Dacor Страницы: 2

Бренд: Farberware Страницы: 24

Miwell-Combi XSL

Бренд: V-ZUG Страницы: 64

Бренд: Smeg Страницы: 26

Бренд: GE Страницы: 3

Бренд: Elba Страницы: 27

Бренд: Palsonic Страницы: 14

Бренд: Smeg Страницы: 29

Бренд: Daewoo Страницы: 37

Бренд: linarie Страницы: 12

Бренд: ElectrIQ Страницы: 16

Бренд: Danby Страницы: 33

Бренд: NEFF Страницы: 72

Бренд: Oster Страницы: 19

Бренд: Zigmund & Shtain Страницы: 47

MKO 908-PR M BK

Бренд: MASTER KITCHEN Страницы: 28

Бренд: Samsung Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды