LG GoldStar MS-133SE страница 15 Скачать руководство пользователя | Manualshive

Страница: 15 / 39

background image

G. MAGNETRON REMOVAL

1) Disconnect the leadwire from the magnetron.
2) Carefully remove the mounting screws holding the

magnetron and the waveguide.

3) Remove the magnetron Ass’y until the tube is clear

from the waveguide.

NOTE:
1. When removing the magnetron, make sure its

dome does not hit any adjacent parts, or it may be
damaged.

2. When replacing the magnetron, be sure to install

the magnetron gasket in the correct position and
be sure that the gasket is in good condition.

3. After replacing the magnetron, check for microwave

leakage with a survey meter around the
magnetron. Microwave energy must be below the

limit of 5 mW/cm

2

. (With a 275 ml. water load).

Make sure that gasket is rigidly attached to the

magnetron. To prevent microwave leakage,
tighten the mounting screws properly, making sure
there is no gap between the waveguide and the
magnetron.

H. HIGH VOLTAGE TRANSFORMER

REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from magnetron, high voltage

transformer, and capacitor.

3) Remove the screw holding the high voltage

transformer to the base-plate.

I. FAN MOTOR ASSEMBLY REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from fan motor, noise filter

and high voltage capacitor.

3) Remove the two screws holding the suction guide

Ass’y to the oven cavity and remove the high voltage
diode earth screw.

4) Remove the screw of the capacitor bracket.
5) Remove the two screws holding the fan motor Ass’y to

the suction guide Ass’y.

J. HIGH VOLTAGE CAPACITOR AND

DIODE REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from the fan motor, noise

filter and high voltage capacitor.

3) Remove the screw holding the suction guide Ass’y to

the oven cavity and remove the high voltage diode
earth screw.

4) Remove the screw holding the high voltage capacitor

bracket.

5-5

Waveguide

Lamp

Air Duct

Magnetron

Magnetron
Gasket

Magnetron

Dome
Waveguide
Bracket

H.V.

Diode

Suction

Guide

Fan Motor

Ass'y

H.V.

Capacitor

«
...
13
14
15
16
17
...
»

Содержание GoldStar MS-133SE








































Отзывы:

Нет отзывов

Похожие инструкции для GoldStar MS-133SE

Бренд: Dacor Страницы: 2

In-A-Drawer MMDV30S

Бренд: Dacor Страницы: 24

Professional + 100

Бренд: Rangemaster Страницы: 36

Бренд: Rangemaster Страницы: 40

Бренд: Rangemaster Страницы: 32

Бренд: Panasonic Страницы: 78

Бренд: Hamilton Beach Страницы: 20

Бренд: Daewoo Страницы: 33

Бренд: Daewoo Страницы: 33

Бренд: Henkel Страницы: 7

Бренд: CDA Страницы: 12

Бренд: Insignia Страницы: 21

Бренд: Daewoo Страницы: 24

Бренд: Hansa Страницы: 56

Бренд: Caloric Страницы: 15

Бренд: Fagor Страницы: 68

Бренд: Dometic Страницы: 28

Бренд: JUNO Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды