LG GoldStar MS-113YE Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 35

background image

H. HIGH VOLTAGE TRANSFORMER

REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from magnetron, high voltage

transformer, and capacitor.

3) Remove the screw holding the high voltage

transformer to the baseplate.

I. FAN MOTOR ASSEMBLY REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from fan motor, noise filter

and high voltage capacitor.

3) Remove the two screws holding the the suction guide

ASSÕY to the oven cavity and remove the high voltage
diode earth screw.

4) Remove the two screws holding the fan motor ASSÕY

to the suction guide ASSÕY.

J. HIGH VOLTAGE CAPACITOR AND

DIODE REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from fan motor, noise filter

and high voltage capacitor.

3) Remove the screw holding the suction guide ASSÕY to

the oven cavity and remove the high voltage diode
earth screw.

4) Remove the screw holding the high voltage capacitor

bracket.

K. INTERLOCK SYSTEM

1) INTERLOCK MECHANISM

The door lock mechanism is a device which has
been specially designed to eliminate completely
microwave activity when the door is opened during
cooking and thus to prevent the danger resulting
from the microwave leakage.

2) MOUNTING OF THE PRIMARY/MONITOR/

SECONDARY SWITCHES TO THE LATCH
BOARD

3) INSTALLATION AND ADJUSTMENT OF THE

LATCH BOARD TO THE OVEN ASSEMBLY

¥ Mount the latch b oard to the oven assembly.
¥ Adjust the latch board in the arrow direction so that

oven door will not have any play in it when the door
is closed.

¥ Tighten the mounting screw.
¥

Check for play in the door by pushing the door
release button. Door movement should be less
than 0.5 mm. (1/64 inch)

Don't push the door release button while making this
adjustment. Make sure that the latch moves
smoothly after adjustment is completed and that the
screws are tight. Make sure the primary, monitor,
and secondary switches operate properly by
following the continuity test procedure.

5-6

PRIMARY
SWITCH

ADJUSTMENT
DIRECTION

MONITOR
SWITCH

SECONDARY
SWITCH

H.V.
Transformer

Suction
Guide

Noise Filter

H.V.
Diode

H.V.
Capacitor

Fan Motor
ASS'Y

«
...
14
15
16
17
18
...
»

Содержание GoldStar MS-113YE




































Отзывы:

Нет отзывов

Похожие инструкции для GoldStar MS-113YE

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 119

Бренд: Panasonic Страницы: 66

Бренд: Panasonic Страницы: 30

CombiSteamer V6000

Бренд: V-ZUG Страницы: 4

Бренд: Daewoo Страницы: 20

Бренд: Russell Hobbs Страницы: 13

Бренд: INNOLIVING Страницы: 28

Бренд: Daewoo Страницы: 20

Бренд: P&C Страницы: 11

Millennia DO130S

Бренд: Dacor Страницы: 36

Бренд: Unox Страницы: 36

NN-GT578SBJQ OEM 27L JLFSMWG002

Бренд: John Lewis Страницы: 24

Бренд: Euro Appliances Страницы: 24

Бренд: V-ZUG Страницы: 52

Designer DDMW01440WG1

Бренд: Danby Страницы: 17

Бренд: Frigidaire Страницы: 27

Бренд: Frigidaire Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды