LG GoldStar MS-113YE Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 35

background image

5-8

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.

(Ohm-meter scale: Rx1 and Rx100)
¥ Primary winding
¥ Secondary winding
¥ Filament winding

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
¥ Primary winding to ground
¥ Filament winding to ground

1. Measure the resistance.

(Ohm-meter scale: Rx1)
¥ Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
¥ Filament to chassis

Approx.: 0.2 ~ 0.4 ohm
Approx.: 60 ~ 90 ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

FILAMENT
WINDING

PRIMARY
TERMINAL

COMPONENT TEST PROCEDURE

«
...
16
17
18
19
20
...
»

Содержание GoldStar MS-113YE




































Отзывы:

Нет отзывов

Похожие инструкции для GoldStar MS-113YE

Бренд: Adexa Страницы: 7

Бренд: Dacor Страницы: 2

In-A-Drawer MMDV30S

Бренд: Dacor Страницы: 24

Combi Duo 6x1/1 GN / 6x1/1 GN

Бренд: Rational Страницы: 20

Бренд: Franke Страницы: 15

Бренд: Logik Страницы: 32

Бренд: Scarlett Страницы: 8

Бренд: Oster Страницы: 3

Бренд: Omega Страницы: 20

Бренд: Lang Страницы: 28

Бренд: P&C Страницы: 11

Бренд: T-Fal Страницы: 48

Бренд: Magic Chef Страницы: 18

Бренд: Cuisinart Страницы: 27

Бренд: Cookology Страницы: 25

Бренд: Lang Страницы: 24

Бренд: V-ZUG Страницы: 28

Бренд: Gaggenau Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды