LG GB175 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 158

LG GB175 Скачать руководство пользователя страница 23

-23-

3.2 Power Amplifier Module (SKY77518)

Figure.3-2-1 SKY77518 FUNCTIONAL BLOCK DIAGRAM

The SKY77518-21 is a transmit and receive front-end module (FEM) with Integrated Power
Amplifier Control (iPAC.) for dual-band cellular handsets comprising GSM900 and DCS1800
operation. Designed in a low profile, compact form factor, the SKY77518-21 offers a complete
Transmit VCO-to- Antenna and Antenna-to-Receive SAW filter solution. The FEM also supports
Class 12 General Packet Radio Service (GPRS) multi-slot operation.

The module consists of a GSM900 PA block and a DCS1800 PA block, impedance-matching

circuitry for 50

Ω

input and output impedances, TX harmonics filtering, high linearity and low

insertion loss PHEMT RF switches, diplexer and a Power Amplifier Control (PAC) block with
internal current sense resistor. A custom BiCMOS integrated circuit provides the internal PAC
function and decoder circuitry to control the RF switches. The two Heterojunction Bipolar
Transistor (HBT) PA blocks are fabricated onto a single Gallium Arsenide (GaAs) die. One PA
block supports the GSM900 band and the other PA block supports the DCS1800 band. Both PA
blocks share common power supply pads to distribute current. The output of each PA block and
the outputs to the two receive pads are connected to the antenna pad through PHEMT RF
switches and a diplexer. The GaAs die, PHEMT die, Silicon (Si) die
and passive components are mounted on a multi-layer laminate substrate. The assembly is
encapsulated with plastic overmold.

Band selection and control of transmit and receive modes are performed using two external

control pads. The band select pad (BS) selects between GSM and DCS modes of operation. The
transmit enable (TX_EN) pad controls receive or transmit mode of the respective RF switch (TX =
logic 1). Proper timing between transmit enable (TX_EN) and Analog Power Control (VRAMP)
allows for high isolation between the antenna and TXVCO while the VCO is being tuned prior to
the transmit burst.

The SKY77518-21 is compatible with logic levels from 1.2 V to VCC for BS and TX_EN pads,

depending on the level applied to the VLOGIC pad. This feature provides additional flexibility for
the designer in the selection of FEM interface control logic.

«
...
21
22
23
24
25
...
»

Содержание GB175































































































































































Отзывы:

Нет отзывов