background image

Use the instructions under option 2 or 3 if your

home has a 3-wire receptacle (NEMA type 10-30R).

Use option 2 if local codes and ordinances permit

the connection of a chassis ground to the neutral

connector. If this is not permitted, use option 3.

Review the following options to determine the appropriate electrical connection for your home

3-1. Connection with a Power Supply Cord.

If this type is available at your home. you will be

connecting to a fused disconnect or circuit breaker

box

Important :Grounding through the neutral conductor

is prohibited for (1) new branch-circuit installations,

(2) mobile homes, and (3) recreational vehicles, and

(4) areas where local codes prohibit grounding through

the neutral conductor.
Prepare minimum 5 ft(1.52 m) of length in order for

dryer to be replaced.
First, peel 5 inch (12.7 cm) of covering material from

end. Make a 5 inch of ground wire bared. After cutting

1

1

/

2

inch (3.8 cm) from 3 other wires. peel insulation

back 1inch (2.5 cm). Make ends of 3 wires a hook

shape. 

Then, put the hooked shape end of the wire under the

screw of the terminal block(hooked end facing rightward)

and pinch the hook together and screw tightly.

Use the instructions under option 1 if your home

home has a 4-wire receptacle (NEMA type 14-30R).

If this type is available at your home. you will be

connecting to a fused disconnect or circuit breaker

box

1. Connect neutral wire(white) of power cord to center

terminal block screw.

2. Connect red and black wire to the left and right

terminal block screws.

3. Connect ground wire(green) of power cord to external

ground screw and move neutral ground wire of

appliance and connect it to center screw.

4. Make sure that the strain relief screw is tightened. 

and be sure that all terminal block nuts are on tight and

power cord is in right position.

1"

(2.5 cm)

5"

(12.7 cm)

3-wire direct

4-wire receptacle 

(NEMA type14-30R) 

3-wire receptacle 

(NEMA type10-30R)  

4-wire direct

5"

(12.7 cm)

4-wire connection : Direct wire

1"

(2.5 cm)

5"

(12.7 cm)

 F

 a

 b

 E

 D

 C

FOR LG TECHNICIAN

9

Содержание DLEX4270 Series































































Отзывы: