LG DLEX4270 Series Скачать руководство пользователя

Страница: 22 / 62

PROBLEM

•

This is normal.

•

Steam is released at different stages of the cycle

for each option.

Cannot see steam

vapor at the

beginning of cycle.

•

MORE TIME pressed.

•

Pressing the MORE TIME button adjusts the

load size from 1to 5 articles or a big load

indicated by in the display.

The display shows:

•

STEAM FRESH™ did

not remove odor

completely.

•

Fabrics containing strong odors should be washed in

a normal cycle.

Odors remain in

clothing after

STEAM FRESH™.

POSSIBLE CAUSES

SOLUTIONS

DISPLAY

Thermistor of blower

housing

Outlet thermistor open or shorted.

tE1

CHECKING PART

CAUSE

•

tE1 error is displayed in the

drying cycle or test mode.

Thermistor of blower

housing

Outlet thermistor open or shorted.

tE2

•

tE2 error is displayed in the

drying cycle or test mode.

Thermistor of steam

generator

Steam generator thermistor open

or shorted.

tE4

•

tE4 error is only displayed in the

test mode.

•

Replace the steam generator.

Water supply pump

When the pump valve is less than

10 in the test mode

•

tE5 error is only displayed in the

test mode.

•

Check the connection between

harness wire and connector.

•

Replace the water supply pump.

Steam generator

Wire Connection

(Black-White-Red)

EE PROM Error

Sensors do not detect that steam

generator is full within 60 seconds.

Wire Connection is wrong.

Wire Connection is loose.

EE PROM operation is adnormal.

•

If water in the steam feeder is

EE error is displayed only in the

test mode

not enough this error may be

displayed. Fill the feeder and

restart the cycle.

•

verify proper connection of the

power cord. (Electric dryer only.)

* PS means power supply.

REMARK

8-3. Display Fault/Error Codes

The error codes below will be displayed when attempting to start a drying cycle or after

activating the Diagnostic Test mode.

FOR LG TECHNICIAN

NFC module

NFC module open or shorted

nC is displayed only in the

test mode

NFC module

NFC module is wrong

nU is displayed only in the

test mode

Содержание DLEX4270 Series































































Результаты поиска

Содержание DLEX4270 Series

Отзывы:

Похожие инструкции для DLEX4270 Series

Бренды по названию

Популярные бренды

LG DLEX4270 Series, Руководство по обслуживанию

Результаты поиска

Содержание DLEX4270 Series

Отзывы:

Похожие инструкции для DLEX4270 Series

Бренды по названию

Популярные бренды