LG CM9520 Скачать руководство пользователя страница 33

Страница: 33 / 109

3-4

Does the customer select correctly

the PORT. IN function he or her wants to listen to?

Make sure to connect a cable

between the PORT. IN jack of the unit and the Audio

output jack of a portable device like a MP3 player.

YES

Is “PORT. IN” displayed on VFD?

Make sure to select the PORT. IN function

pressing the AUX/IPOD/PORT. IN button.

YES

Turn the master volume clockwise

for the volume up.

The volume level LEDs around the master volume

will be turned on more and more

while turning it clockwise for the volume up.

YES

Is there any sound

from the selected input source?

Refer to a portable device’s instruction manual

and then check if there is sound output

from it connecting another audio system.

YES

Are the sound spectrum level LED’s

on the left and right side of the front panel

being changed up and down

according to the sound input gain?

The sound spectrum level LED’s will be turned on/off

repeatedly at regular intervals. A speaker cable

might be short-circuited with the chassis ground.

Be careful not to be shorted each other.

YES

Are the speaker cables connected correctly

between the speaker terminals on the unit

and the speakers?

Make sure to connect the cables to each specified

connector tightly on the unit.

Connect the woofer cables to the WOOF SYSTEM

connectors on the rear panel.

YES

The sound is output

from the speakers.

YES

Sound OK

3. NO SOUND IN PORT. IN FUNCTION

TRAINING MASTER

Содержание CM9520














































































































Результаты поиска

Содержание CM9520

Отзывы:

Похожие инструкции для CM9520

Бренды по названию

Популярные бренды

LG CM9520, Руководство по обслуживанию

Результаты поиска

Содержание CM9520

Отзывы:

Похожие инструкции для CM9520

Бренды по названию

Популярные бренды