LG ARWN Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 75

background image

6

Outside Unit

Safety Precautions

Safely dispose of the packing materials.

• Packing materials, such as nails and other metal or wooden

parts, may cause stabs or other injuries.

• Tear apart and throw away plastic packaging bags so that

children may not play with them. If children play with a plastic
bag which was not torn apart, they face the risk of suffocation.

Turn on the power at least 6 hours before
starting operation.

• Starting operation immediately after turning on the main

power switch can result in severe
damage to internal parts. Keep the power switch turned on
during the operational season.

Be very careful about product transportation.

• Only one person should not carry the product if it weighs more than 20 kg.
• Some products use PP bands for packaging. Do not use any PP bands for a means of transportation. It is dangerous.
• Do not touch the heat exchanger fins. Doing so may cut your fingers.
• When transporting the outside unit, suspending it at the specified positions on the unit base. Also support the outside unit

at four points so that it cannot slip sideways.

Do not touch any of the refrigerant piping
during and after operation.

• It can cause a burn or frostbite.

Do not operate the air conditioner with the
panels or guards removed.

• Rotating, hot, or high-voltage parts can cause injuries.

Do not directly turn off the main power
switch after stopping operation.

• Wait at least 5 minutes before turning off the main power

switch. Otherwise it may result in water leakage or other
problems.

Auto-addressing should be done in condition of
connecting the power of all indoor and outdoour
units. Auto-addressing should also be done in
case of changing the indoor unit PCB.

Use a firm stool or ladder when cleaning or
maintaining the air conditioner.

• Be careful and avoid personal injury.

«
...
4
5
6
7
8
...
»

Содержание ARWN Series












































































Отзывы:

Нет отзывов

Похожие инструкции для ARWN Series

Бренд: Panasonic Страницы: 108

R32 Split Series

Бренд: Daikin Страницы: 28

Бренд: Danby Страницы: 34

Бренд: Danby Страницы: 40

Бренд: Nortek Страницы: 12

22-11-2222N-003

Бренд: Maytag Страницы: 26

Бренд: Goodman Страницы: 48

Thru-the-Wall Air Conditioners

Бренд: Friedrich Страницы: 6

Бренд: Linea 2000 Страницы: 94

Бренд: IP Enclosures Страницы: 16

Бренд: Daikin Страницы: 15

Бренд: arovec Страницы: 24

Бренд: Heat Controller Страницы: 18

Бренд: Daikin Страницы: 15

Бренд: Daikin Страницы: 24

Бренд: Haier Страницы: 32

Бренд: HELLER Страницы: 9

Бренд: Centek Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды