LG ARWN Series Скачать руководство пользователя страница 16

Страница: 16 / 75

Installation

Preparation of Piping

1) Cut the pipes and the cable.

Use the accessory piping kit or the pipes purchased
locally.

Measure the distance between the indoor and the out-
side unit.

Cut the pipes a little longer than measured distance.

Cut the cable 1.5m longer than the pipe length.

2) Burrs removal

Completely remove all burrs from the cut cross section
of pipe/tube.

Put the end of the copper tube/pipe to downward direc-
tion as you remove burrs in order to avoid to let burrs
drop in the tubing.

3) Flaring work

Carry out flaring work using flaring tool as shown below.

Firmly hold copper tube in a bar(or die) as indicated
dimension in the table above.

4) Check

Compare the flared work with figure below.

If flare is noted to be defective, cut off the flared section
and do flaring work again.

Main cause of gas leakage is defect in flaring work. Carry out correct flaring work in the following procedure.

Pipe

" A "

Gas

Liquid

Gas

Liquid

<5.6(19,100)

1/2"

1/4"

0.5~0.8

0~0.5

<16.0(54,600)

5/8"

3/8"

0.8~1.0

0.5~0.8

<22.4(76,400)

3/4"

3/8"

1.0~1.3

0.5~0.8

Indoor unit
[kW(Btu/h]

Copper

tube

Slanted Uneven Rough

Pipe

Reamer

Point down

Bar

Copper pipe

Clamp handle

Red arrow mark

Cone

Yoke

Handle

Bar

"A"

Inclined

Inside is shining without scratches.

Smooth all round

Even length

all round

Surface

damaged

Cracked Uneven

thickness

= Improper flaring =

Outside Unit

Содержание ARWN Series












































































Результаты поиска

Содержание ARWN Series

Отзывы:

Похожие инструкции для ARWN Series

Бренды по названию

Популярные бренды

LG ARWN Series, Руководство по установке

Результаты поиска

Содержание ARWN Series

Отзывы:

Похожие инструкции для ARWN Series

Бренды по названию

Популярные бренды