LG ARUB100LT3 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 133

background image

Installation of Outdoor Unit, HR Unit, Indoor Unit Refrigerant Pipe

3 pipes are connected to the HR unit from the outdoor unit, classified into liquid pipe, low pressure gas pipe and
high pressure gas pipe depending on status of refrigerant passing through the pipe.

You must connect 3 pipes from outdoor unit to HR unit.

For connection between indoor unit and HR unit, you must connect both liquid pipe and gas pipe from the HR
unit to the indoor unit. In this case, connect them to the indoor unit starting from No.1 connection port of the HR
unit (the port number is displayed on ports of the HR unit). Use auxiliary flare as annexed parts in connection to
the indoor unit.

Gas pipe

Gas pipe

Liquid pipe

Liquid pipe

HR Unit

1 2

3 4

Low pressure
Gas pipe

Liquid pipe

High pressure
Gas pipe

CAUTION:

Whenever connecting the indoor units with the HR unit, install the indoor units in numerical order from No.1.

Ex) In case of installing 3 indoor units : No. 1, 2, 3 (O), No. 1, 2, 4 (X), No.1, 3, 4 (X), No.2, 3, 4 (X).

Installation procedure for HR unit

Six-sided Nut
(M10 or M8)

Hanger metal

Hanger metal

Hanger metal

Flat washer

Flat washer

Flat washer
(M10)

Hanging bolt

Hanging bolt

Hanging bolt
(M10 or M8)

A

Insulation

1. Using an insert-hole-in- anchor, hang the hanging bolt.

2. Install a hexagon nut and a flat washer (locally-procured)to the hanging bolt as shown

in the figure in the bottom, and fit the main unit to hang on the hanger metal.

3. After checking with a level that the unit is level, tighten the hexagon nut.

* The tilt of the unit should be within ±5° in front/back and left/right.

4. This unit should be installed suspended from ceiling and side A should always be

facing up.

5. Insulate not used pipes completely as shown in the figure.

Installation Manual

23

Refrigerant piping installation

ENGLISH

«
...
21
22
23
24
25
...
»

Содержание ARUB100LT3






































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARUB100LT3

Бренд: Haier Страницы: 52

IND-AHC-TRF-2X2-UVC-R1-120V

Бренд: Larson Electronics Страницы: 3

Бренд: Baxi Страницы: 180

CS-25V1A-H1; CS-35V1A-E2; CS-50V9A-S; CS-70V9A-T

Бренд: Chigo Страницы: 66

Бренд: Trane Страницы: 24

Бренд: Bryant Страницы: 36

Бренд: Bionaire Страницы: 25

Бренд: Midea Страницы: 84

Бренд: Kaysun Страницы: 16

Бренд: Toyotomi Страницы: 48

Бренд: Fedders Страницы: 16

Бренд: Daikin Страницы: 20

Бренд: TriStar Страницы: 48

NANO AIR2 CLASSIC

Бренд: aldes Страницы: 40

GWH09MA-K3DNA3L

Бренд: Gree Страницы: 89

Бренд: Daikin Страницы: 114

Бренд: Olimpia splendid Страницы: 144

Бренд: innovair Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды