LG ARUB100LT3 Скачать руководство пользователя страница 15

Страница: 15 / 133

Lifting method

Installation Manual

ENGLISH

• When carrying the suspended, unit pass the ropes under the unit and use the two suspension points each at

the front and rear.

• Always lift the unit with ropes attached at four points so that impact is not applied to the unit.

• Attach the ropes to the unit at an angle of 40° or less.

Lifting method

CAUTION

Be very careful while carrying the product.

• Do not have only one person carry product if it is more than 20 kg.

• PP bands are used to pack some products. Do not use them as a mean for transportation because they

are dangerous.

• Do not touch heat exchanger fins with your bare hands. Otherwise you may get a cut in your hands.

• Tear plastic packaging bag and scrap it so that children cannot play with it. Otherwise plastic packaging

bag may suffocate children to death.

• When carrying in Outdoor Unit, be sure to support it at four points. Carrying in and lifting with 3-point

support may make Outdoor Unit unstable, resulting in a fall.

• Use 2 belts of at least 8 m long.

• Place extra cloth or boards in the locations where the casing comes in contact with the sling to prevent

damage.

• Hoist the unit making sure it is being lifted at its center of gravity.

Weight per Capacity

Locking points for

transportation ropes

Forklift Carrying Guide

Forklift Carrying Hole

Chassis

Capacity(HP)

Weight(kg)

UX2

190

240

UX3

270

320

330

Содержание ARUB100LT3






































































































































Результаты поиска

Содержание ARUB100LT3

Отзывы:

Похожие инструкции для ARUB100LT3

Бренды по названию

Популярные бренды

LG ARUB100LT3, Руководство по установке

Результаты поиска

Содержание ARUB100LT3

Отзывы:

Похожие инструкции для ARUB100LT3

Бренды по названию

Популярные бренды