background image

Safety Precautions

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions must be followed.

n

Be sure to read before installing the air conditioner.

n

Be sure to observe the cautions specified here as they include important items related to safety.

n

Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the
following indications.

n

Meanings of symbols used in this manual are as shown below.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

Be sure not to do.

Be sure to follow the instruction.

Installation Manual  

5

ENGLISH

Installation

• Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated

circuit.
- There is risk of fire or electric shock.

• For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized

Service Center.
- Do not disassemble or repair the product. There is risk of fire or electric shock.

• Always ground the product.

- There is risk of fire or electric shock.

• Install the panel and the cover of control box securely.

- There is risk of fire or electric shock.

• Always install a dedicated circuit and breaker.

- Improper wiring or installation may cause fire or electric shock

• Use the correctly rated breaker or fuse.

- There is risk of fire or electric shock.

Содержание ARNU093SEL2
























Отзывы: