LG ABUQ60LM3T1 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 24

background image

12

WIRING CONNECTION

ENGLISH

Connecting the cable to Outdoor Unit

Remove the side panel for wiring connection.

Use the cord clamp to fix the cable.

Earthing work
- Connect the cable of diameter more to the earthing terminal provided in the control box and do

earthing.

* Make sure the rubber bushes are

properly used in knock-out holes after
connecting main power.

Cord clamp

Power cable
terminal

Connecting
cable terminal

Power cable terminal
Connecting cable terminal

• The circuit diagram is not subject to change without notice.

• Be sure to connect wires according to the wiring diagram.

• Connect the wires firmly, so that not to be pulled out easily.

• Connect the wires according to color codes by referring the wiring diagram.

• The Power cable connected to the unit should be selected according to the following

specifications.

CAUTION

!

«
...
10
11
12
13
14
...
»

Содержание ABUQ60LM3T1

























Отзывы:

Нет отзывов

Похожие инструкции для ABUQ60LM3T1

Бренд: Galletti Страницы: 20

Бренд: Keller Страницы: 2

Бренд: Zibro Страницы: 2

Бренд: Klarstein Страницы: 64

SA3BF4M2SN Series

Бренд: Nortek Страницы: 12

Бренд: Telair Страницы: 32

Бренд: Levoit Страницы: 12

Бренд: NewAir Страницы: 15

Бренд: GE Страницы: 36

DO-CH-ACL150DRT

Бренд: Dutch originals Страницы: 48

Бренд: DayRelax Страницы: 100

Бренд: Venmar Страницы: 20

Бренд: RZB Lighting Страницы: 8

Бренд: Sinclair Страницы: 38

Depuro Plus 230

Бренд: Vortice Страницы: 72

Бренд: Rowenta Страницы: 44

MDV MOB02-18HFN8-QRD0GW

Бренд: aircon Страницы: 120

Бренд: Daikin Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды