LG 47SL9000, Руководство по обслуживанию

Страница: 11 / 36

4. Total Assembly line process
4.1. Adjustment Preparation
· W/B Equipment condition
CA210 : CH 14(LED), Test signal : Inner pattern (85IRE)
· Above 5 minutes H/run in the inner pattern. (“power on” key
of adjust remote control)
* Connecting picture of the measuring instrument
(On Automatic control)
Inside PATTERN is used when W/B is controlled. Connect to
auto controller or push Adjustment R/C POWER ON ->
Enter the mode of White-Balance, the pattern will come out
* Auto-control interface and directions
1) Adjust in the place where the influx of light like floodlight
around is blocked. (illumination is less than 10 lux).
2) Adhere closely the Color Analyzer (CA210) to the module
less than 10cm distance, keep it with the surface of the
Module and Color Analyzer’s Prove vertically.(80~100°).
3) Aging time
- After aging start, keep the power on (no suspension of
power supply) and heat-run over 15minutes.
- Using ‘no signal’ or ‘full white pattern’ or the others,
check the back light on.
• Auto adjustment Map(RS-232C)
RS-232C COMMAND
[CMD Format]
START 6E A 50 A LEN A 03 A CMD A 00 A VAL A CS A STOP
- LEN : Number of Data Byte to be send
- CMD : Command
- VAL : FOS Data
- CS : Checksum of sent Data
- A : Acknowledge
Ex) [Send : JA_00_DD] / [Ack : A_00_okDDX]
[CMD ID DATA]
Wb 00 00 White Balance Start
Wb 00 ff White Balance End
In the SET applied LED module, as to physical characteristics
of LED Module, the sets takes a 120 minutes by aging time to
stabilize a color coordinates. So White Balance Control
equipments get the SET Aging Time from SET and then going
to control the W/B by revise color coordinates in the each time
Cautions) The Time Table of color coordinates by SET Aging Time
** Caution **
Color Temperature : COOL, Medium, Warm.
One of R Gain/ G Gain/ B Gain should be kept on 0xC0, and
adjust other two lower than C0.
(when R/G/B Gain are all C0, it is the FULL Dynamic Range
of Module)
* Manual W/B process using adjusts Remote control.
Dynamic contrast : off
Dynamic color : off
OPC : off
Energy saving mode : off
• After enter Service Mode by pushing “ADJ” key,
• Enter White Balance by pushing “
G ” key at “3. White
Balance”.
- In the SET applied LED module, as to physical
characteristics of LED Module, the sets takes a 120
minutes by aging time to stabilize a color coordinates. So
White Balance Control equipments get the SET Aging Time
from SET and then going to control the W/B by revise color
coordinates in the each time
- 11 - LGE Internal Use Only Copyright ©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
Cool 13,000k ºK X=0.269(±0.002)
Y=0.273(±0.002) <Test Signal>
Medium 9,300k ºK X=0.285(±0.002) Inner pattern
Y=0.293(±0.002) (216gray,85IRE)
Warm 6,500k ºK X=0.313(±0.002)
Y=0.329(±0.002)
Full White Pattern
COLOR
ANALYZER
TYPE: CA-210
RS-232C Communication
CA-210
RS-232C COMMAND MIN CENTER MAX
[CMD ID DATA] (DEFAULT)
Cool Mid Warm Cool Mid Warm
R Gain jg Ja jd 00 172 192 192 255
G Gain jh Jb je 00 172 192 192 255
B Gain ji Jc jf 00 192 192 172 255
R Cut 64 64 64 128
G Cut 64 64 64 128
B Cut 64 64 64 128
H/R Time Cool Medium Warm
(Min) X Y X Y X Y
269 273 285 293 313 329
1 ~5 281 297 290 307 318 343
2 6~20 280 288 289 301 317 338
3 21~30 278 285 287 297 316 334
4 31~ 276 283 285 293 313 329