LG-Ericsson iPECS SBG-1000 Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 197

background image

iPECS SBG-1000 User Manual (IP-PBX Features)

3-3

3.1.1.3

Tnet Attributes

Each LM (Local MFIM), which is part of a Central Control Network, must be defined with the IP
Address of the CM (Central MFIM) as well as the LM configuration data that will be sent to the CM
at the time the LM registers with the CM. Total port counts define the ports, which are allocated in
the CM database for use by devices registered to the LM. The number of ports defined in the
database of each LM must be equal or less than the ports defined in the CM for the LM in order to
register properly.

Table 3.1.1.3 Tnet Attributes

ATTRIBUTE

DESCRIPTION

RANGE

DEFAULT

Register Enable

This field informs the LM to attempt registration with the
CM. This field must be set to ON for proper registration.

0: OFF

1: ON

OFF

IP Address

This field defines the IP address of the CM that will be
used by the LM.

IPv4 address

IPKTS Port number

In the TNET environment, the IP KTS protocol signaling
UDP port is defined. At present this field is not used, do
not change this port number.

0000-9999

5588

Total no of port

This field defines the total number of ports the LM will
request be allocated by the CM for devices attached to the
LM. This value must be equal to or less than the port
count in the CM for the LM devices.

000-999

0

Polling Count

This field defines the maximum polling failures an LM
considers a WAN fault

00-99

05

Polling interval

This field defines the interval time between LM to CM
polling attempts.

00-99

02

3.1.2 Station Registration

3.1.2.1

Station List & Replacement

Registered station list is displayed on this page; a user can see IP address, device type, version of
device, connect status of registered devices. In addition, a user can change the logical number of
station, station name, remark and so on.

3.1.2.2

Registration Table

By entering device MAC addresses, the system will allow the device to register.

While  initial  installation,  you  may  want  to  register  all  connected  stations  without  MAC  address
programming.  Then  you  should  select  “All  Stations”  in  front  of  Save  button  on  the  “Registration
Table”  web  page  and  click  Save  button.  After  all  connected  stations  are  registered,  you  should
select  back  to “MAC  matched  Station  Only”  to  prevent  unintended  device  registration. While  “All
Stations” can be registered, 4

th

LED

– IP-PBX LED will be flashing more rapidly as warning sign.

«
...
161
162
163
164
165
...
»

Содержание iPECS SBG-1000






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для iPECS SBG-1000

Бренд: TempAlert Страницы: 22

Бренд: Gardena Страницы: 21

Бренд: Nomadix Страницы: 204

Бренд: RTA Страницы: 68

Бренд: Exsys Страницы: 27

Бренд: Gree Страницы: 31

Бренд: Cisco Страницы: 4

Бренд: ABB Страницы: 11

Бренд: Eaton Страницы: 67

Бренд: Eaton Страницы: 93

Бренд: Eaton Страницы: 276

Бренд: Toro Страницы: 40

Бренд: Luminext Страницы: 8

Бренд: ZyXEL Communications Страницы: 2

Бренд: evertz Страницы: 34

Бренд: Ness Страницы: 48

VMG1312-B Series

Бренд: ZyXEL Communications Страницы: 376

Бренд: ActionTec Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды