LFA RTP 9 Скачать руководство пользователя страница 44

Страница: 44 / 95

Replace the Fill Tray

6. Loosely attach the Fill Tray Scraper and Take-Off Blade on the new Fill Tray with a
crosshead screwdriver.
7. Place the new Fill Tray on the Turret and align it with the Fill Tray Height Adjusters' holes.

8. Screw in the Fill Tray Thumb Bolts through the Fill Tray and Fill Tray Height Adjusters.

8.1 Note: Please refer to the Fill Tray Height adjustment instructions on page 22 for

calibration.
9. Tighten the Fill Tray Scraper and Take-Off Blade with a crosshead screwdriver.

9.1 Note: It is important to make sure that the Fill Tray Scraper blade is firmly up against the

Die Table of the Turret. To do this, push down on the top of the blade while tightening the

screws that hold it in place. The Take-Off Blade needs to not be touching the Die Table and

should be mounted approximately 1/3 of the height of the tablet from the surface of the Die

Table.
10. Shut the Perspex Casing door.
11. Resecure the Hopper to the Perspex Casing with an Allen key.

11.1 Note: Be sure the Hopper's end is situated in the Fill Tray's largest section and to

the far-most right.

Содержание RTP 9
































































































Результаты поиска

Содержание RTP 9

Отзывы:

Похожие инструкции для RTP 9

Бренды по названию

Популярные бренды

LFA RTP 9, Руководство пользователя

Результаты поиска

Содержание RTP 9

Отзывы:

Похожие инструкции для RTP 9

Бренды по названию

Популярные бренды