Lexmark Optra ep Скачать руководство пользователя страница 94

Страница: 94 / 143

4026-0XX

4-14

Thermal Fuse Removal (06A/06B/06D/06J/070)

1. Remove the top cover.

2. Remove the fuser upper frame assembly.

3. Remove the two screws mounting the thermal fuse.

4. Remove the thermal fuse.

Thermostat Removal (06C/06F/071)

1. Remove the top cover.

2. Remove the fuser upper frame assembly.

3. Remove the two thermostat mounting screws.

4. Remove the fuser thermostat.

Thermistor Removal

1. Remove the fuser lower frame assembly.

2. Remove the screw that holds the thermistor to the left side of

the fuser lower frame assembly.

3. Note the routing of the thermistor cable and remove the

thermistor.

Transfer Unit Removal

Models 4026-06A, 06B, 06D, 06J and 070

1. Remove the top cover.

2. Remove the screw holding the right transfer assembly bracket.

3. Note the mounting and orientation of the left and right transfer

assembly tension springs.

4. Remove the transfer assembly.

5. Remove the transfer assembly tension springs.

Содержание Optra ep
















































































































































Результаты поиска

Содержание Optra ep

Отзывы:

Похожие инструкции для Optra ep

Бренды по названию

Популярные бренды

Lexmark Optra ep, Руководство по обслуживанию

Результаты поиска

Содержание Optra ep

Отзывы:

Похожие инструкции для Optra ep

Бренды по названию

Популярные бренды