Lexmark Optra ep Скачать руководство пользователя страница 71

Страница: 71 / 143

4026-0XX

Diagnostic Aids 3-4

Service Diagnostic Test Page

The service diagnostic test page includes registration marks to aid in
adjusting print registration and also includes the installed printer
base code level. The service test page displays the user default
values for the following:

Top Margin Offset

Left Margin Offset

Printer Page Count

Permanent Page Count

Print Darkness Setting

PQET Setting (on/off)

Toner Saver (on/off)

Print Resolution

Perform the following steps to print the Service Diagnostic Test
Page:

1. Turn the printer off.

2. Open the top cover.

3. Press and hold the operator panel button as you turn on the

printer.

4. Wait until the Error LED comes on solid.

5. Close the top cover.

6. The Ready LED is on solid and the Data LED blinks continu-

ously.

7. When the test is complete the Ready LED goes off and the Data

LED continues to blink.

8. Press the operator panel button briefly.

9. The Ready and Data LEDs blink and the Service Diagnostic

Test Page prints. The test page requires several seconds to
start printing.

10. When the test page has finished printing the Ready LED comes

on solid and Data LED goes off.

Note: After the diagnostic test page prints, the printer automatically
exits the diagnostic mode and returns to the normal mode.

Содержание Optra ep
















































































































































Результаты поиска

Содержание Optra ep

Отзывы:

Похожие инструкции для Optra ep

Бренды по названию

Популярные бренды

Lexmark Optra ep, Руководство по обслуживанию

Результаты поиска

Содержание Optra ep

Отзывы:

Похожие инструкции для Optra ep

Бренды по названию

Популярные бренды