Lexmark C 540n Скачать руководство пользователя страница 88

Страница: 88 / 262

2-54

Service Manual

5025-2xx, 4xx

USB service check

Print a menu settings page.

Note:

If two option trays are used, the 650

sheet will appear as tray 2, and the 550 sheet
tray will appear as tray 3.

Are all the attached option trays listed on the
first page of the menu settings pages?

Go to step 9.

• If the 550 sheet option

failed to appear,

go to

step 9.

• If the 650 sheet tray

failed to appear, go to
step 10.

1. Remove the 650 sheet tray from the printer
2. Attach the 550 sheet tray directly to the

printer

3. Print a page from the 550 sheet tray.

Did the page print?

Go to step 11.

Replace the 550 sheet tray.

With only the 650 sheet tray attached to the
printer, print a page from the 650 sheet tray.

Did the page print?

Go to step 11.

Replace the 650 sheet tray.

1. Turn off the printer.
2. Remove the rear shield.

see

“Top cover

assembly removal” on page 4-13

3. Disconnect the cable at JOPT1 on the

controller board.

urn the printer on.

5. Measure the voltages below:

Are the voltages correct?

Consult your next level
support.

Replace the controller
board. See

“Controller

board removal” on
page 4-20

Step

Questions / actions

Yes

Is the USB cable properly connected to the
printer and host PC?

Go to step 2.

Properly connect the cable
at both ends.

Try a different USB cable.

Does this fix the issue?

Issue fixed.

Go to step 3.

Connect a different device to the USB cable.

Did the host PC see the device?

Replace the Controller
board.See

“Controller

board removal” on
page 4-20

There is an issue with the
host machine.

Step

Questions / actions

Yes

JOPT1

Pin

Voltage

Ground

+24V

Ground

+5V

Ground

Содержание C 540n







































































































































































































































































Результаты поиска

Содержание C 540n

Отзывы:

Похожие инструкции для C 540n

Бренды по названию

Популярные бренды

Lexmark C 540n, Руководство по обслуживанию

Результаты поиска

Содержание C 540n

Отзывы:

Похожие инструкции для C 540n

Бренды по названию

Популярные бренды