Lexmark 7000 Color Jetprinter Скачать руководство пользователя страница 61

Страница: 61 / 85

Preventive Maintenance 6-1

4092

6. Preventive Maintenance

This chapter contains the lubrication specifications. Follow these
recommendations to prevent problems and maintain optimum
performance.

Lubrication Specifications

Lubricate only when parts are replaced or as needed, not on a
scheduled basis. Use grease P/N 1329301 to lubricate the following:

•

All gear mounting studs.

•

The left and right ends of the large feed roller at the side frames.

•

Both ends of the sheet feeder pick roll shaft at the side frames.

•

The carrier to carrier frame engagement.

•

The carrier guide rod, and carrier guide rod bearings.

•

Both ends of the exit roller shaft.

Содержание 7000 Color Jetprinter






















































































Результаты поиска

Содержание 7000 Color Jetprinter

Отзывы:

Похожие инструкции для 7000 Color Jetprinter

Бренды по названию

Популярные бренды

Lexmark 7000 Color Jetprinter, Руководство по обслуживанию

Результаты поиска

Содержание 7000 Color Jetprinter

Отзывы:

Похожие инструкции для 7000 Color Jetprinter

Бренды по названию

Популярные бренды