Lexmark 7000 Color Jetprinter Скачать руководство пользователя страница 50

Страница: 50 / 85

Repair Information 4-14

4092

Paper Feed Motor Removal

1. Remove the front cover.

2. Remove the rear cover.

3. Remove the base assembly.

4. Remove the two screws securing the paper feed motor and

remove the motor. Note the routing of the motor cable.

Paper Guide and EOF Flag Assembly Removal

1. Remove the front cover.

2. Remove the rear cover.

3. Remove the printhead carrier assembly.

4. Remove the carrier frame assembly.

5. Remove the encoder strip.

6. Remove the system board.

7. Remove the three small feed roll springs.

8. Push the locking tabs [A] to the rear and pull the paper guide

down and out of the carrier frame.

Содержание 7000 Color Jetprinter






















































































Результаты поиска

Содержание 7000 Color Jetprinter

Отзывы:

Похожие инструкции для 7000 Color Jetprinter

Бренды по названию

Популярные бренды

Lexmark 7000 Color Jetprinter, Руководство по обслуживанию

Результаты поиска

Содержание 7000 Color Jetprinter

Отзывы:

Похожие инструкции для 7000 Color Jetprinter

Бренды по названию

Популярные бренды